(3)
Adjust the flap ball screws if dimension Y is not equal on the two flap ball screws:
(a)
Push the ALTN ARM switch to put the flap drive system in alternate control.
(b)
Manually turn the torque tubes and the power package, until the ball screw nuts touch the flap ball screw downstops.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-01
ALL ú ú 01 Page 503 ú Jun 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
FOREFLAP
MIDFLAP
FWD
SEE A
JOINT UNIVERSAL GIMBAL BUSHING FLANGE 15. 16. WASHER NUT MIDFLAP
TRANSMISSION
SEE B DIMENSION X FWD BALLSCREW NUT 19. WASHER 17. GIMBAL CAP DOWNSTOP
DIMENSION Y BSEE 18. BOLT BALLSCREW DIMENSION X OR Y
A
STOP
B
Flap Ballscrew Adjustment Figure 501
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-01
ALL ú ú 01 Page 504 ú Feb 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
WARNING: PREVENT FLAP MOVEMENT BEFORE YOU DISCONNECT THE FLAP
_______ TORQUE TUBES. THE FLAPS CAN MOVE FAST TO THE DOWNSTOPS AND CAUSE INJURY TO PERSONS OR CAUSE DAMAGE TO EQUIPMENT.
(c)
Make sure that the flaps do not move.
(d)
Disconnect the flap torque tubes at the transmissions. 1) Remove three screws which attach the coupling sleeve to the
torque tube. 2) Move the coupling sleeve near the gearbox.
(e)
Let the inboard flaps extend until the two ball screw nuts touch the downstops.
(f)
Install the flap torque tubes. 1) Move the coupling sleeve along the flap torque tube. 2) Install the three screws that attach the coupling sleeve to
the flap torque tube.
NOTE: Do not install the lockwire on the bolts at this
____
time.
G. Do a Check of the Inboard Flaps at the Upstop
S 865-012
CAUTION:_______MONITOR THE FLAPS CAREFULLY WHILE THEY RETRACT. THE FLAPS CAN BE DAMAGED BECAUSE OF INCORRECTLY ADJUSTED COMPONENTS.
(1)
Turn the ALTN FLAPS switch to put the inboard flaps in the 5-unit position.
S 865-075
(2)
When the EICAS shows that the flaps are in the 5-unit position, turn the ALTN FLAPS switch to OFF.
S 435-013
(3)
Install the aft roller supports (Ref 27-51-39/401).
(4)
Put the flap control lever in the 5-unit detent.
S 865-014
S 865-015
WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE LE AND TE
_______ FLAPS AND FLAP DRIVE MECHANISMS. THE LE AND TE FLAPS WILL MOVE TO AGREE WITH THE FLAP CONTROL LEVER POSITION WHEN THE ALTERNATE CONTROL IS DISARMED.
(5) Push the ALTN FLAPS ARM switch to put the flap control system in normal control.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-01
ALL ú ú 01 Page 505 ú Oct 10/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 865-016
CAUTION:_______MONITOR THE FLAPS CAREFULLY WHILE THEY RETRACT. THE FLAPS CAN BE DAMAGED BECAUSE OF INCORRECTLY ADJUSTED COMPONENTS.
(6) Pressurize hydraulic system No. 1 (Ref 29-11-00/201).
S 865-069
WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE LE AND TE
_______ FLAPS AND FLAP DRIVE MECHANISMS BEFORE YOU MOVE THE FLAP CONTROL LEVER. WITH HYDRAULIC POWER REMOVED, THE FLAPS WILL MOVE AUTOMATICALLY BY ELECTRICAL POWER WHEN YOU MOVE THE FLAP CONTROL LEVER.
(7) Put the flap control lever in the UP detent to retract the flaps.
NOTE: Control the hydraulic pressure to retract the flaps slowly.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：747-400 AMM 飞机维护手册 飞行操纵 FLIGHT CONTROLS 4(76)
