(4)
AIPC 27-41-05, Fig. 1
(5)
AIPC 27-41-14, Fig. 2
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-41-14
ALL ú ú 01 Page 201 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
BALL STOP SCREW SEE A
STOP NUT BALL HORIZONTAL STABILIZER MECHANISM TRIM DRIVE
STOP BALLSCREW
B BALLNUT STOP
UPPER GIMBAL
A
Stabilizer Position Setting Figure 201
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-41-14
ALL ú ú 01 Page 202 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
SEE A
STABILIZER CENTER SECTION SEE B
STABILIZER (TOP SURFACE) ACCESS
SLIDING BLADE SEAL (HIGHER)
FWD
A
SLIDING
BLADE SEAL
(LOWER) CENTER SECTION STABILIZER
HINGE FITTING DRIVE FITTING MAST (BOTTOM SURFACE)
HINGE FITTING
SHIMS
YOKE BONDING JUMPER
LOWER SEAL DOOR
(EXTENDED) BELL WASHER (2 LOCATIONS)
SPURFWD MAST-TO-CRANK
CRANK-TO-DOOR LINK ROD
LINK ROD
CRANK
B
____THE RIGHT SIDE IS SHOWN; THE LEFT SIDE
NOTE: IS OPPOSITE. STABILIZER SHOWN WITH THE LEADING EDGE IN ZERO DEGREE POSITION. MAKE SURE YOU INSTALL THE CRANK WITH THE SPUR POINTED AS SHOWN.
Horizontal Stabilizer Body Seal Door and Seal Door Mechanism Installation Figure 202
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-41-14
ALL ú ú 05 Page 203 ú Oct 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
(6)
AIPC 27-41-14, Fig. 3
D.
Access
(1)
Location Zone
313 Stabilizer Torsion Box Compartment, LH
314 Stabilizer Torsion Box Compartment, RH
(2)
Access Panel
312A Horizontal Stabilizer Jackscrew Access Door
315A Access Door
E.
Prepare for Removal
S 012-002
(1)
Open the access doors 312A and 315A (AMM 06-09-05/201).
S 492-003
(2)
Attach the safety device to the receptacle on the top surface of the horizontal stabilizer.
S 862-004
(3)
Do this task: "Supply Electrical Power" (AMM 24-22-00/201).
S 862-005
(4)
Do this task: "Supply Hydraulic Power" (AMM 29-11-00/201).
S 862-006
(5)
Set the STAB TRIM 2 and 3 switches on the control stand to ON.
S 862-007
(6)
Use the STAB TRIM ALTN switches to set the stabilizer to the neutral rig position (3 units of trim).
S 862-008
(7)
Set the STAB TRIM 2 and 3 switches to CUTOUT.
S 862-009
(8)
Open these circuit breakers and attach DO-NOT-CLOSE tags:
(a)
P7, Overhead Circuit Breaker Panel
1) 7E7, STAB TRIM L S/O VLV
2) 7E20, STAB TRIM R S/O VLV
S 862-071
(9)
If the hydraulic power is not necessary, do this task: "Remove Hydraulic Power" (AMM 29-11-00/201).
S 862-010
(10)
If the electrical power is not necessary, do this task: "Remove Electrical Power" (AMM 24-22-00/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-41-14
ALL ú ú 09 Page 204 ú Jun 18/01
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：747-400 AMM 飞机维护手册 飞行操纵 FLIGHT CONTROLS 4(11)
