S 226-003
(2)
Measure the body seal door parts for worn areas:
(a)
Remove the parts.
(b)
Use a micrometer or a vernier caliper to measure the parts.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-41-14
ALL ú ú 01 Page 601 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
(c)
Compare the dimensions you measured with the permitted dimensions shown in Fig. 601 or Fig. 602.
(d)
Replace the parts that are not in the tolerance.
(e)
Install the parts.
S 436-004
(3) Do this task: "Horizontal Stabilizer Body Seal Door Installation" (Ref 27-41-14/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-41-14
ALL ú ú 01 Page 602 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
SEE A STABILIZER ACCESS
DRIVE
FITTING STABILIZER
CENTER SECTION
SLIDING BLADE HINGE SEE B (BOTTOM SURFACE)
SEAL (LOWER) FITTING
HINGE FITTING
BONDING
LOWER SEAL DOOR JUMPER
(EXTENDED)
1. BOLT/BUSHING (2 LOCATIONS EACH DOOR)
1
DRIVE ROD
FWD ____THE LOWER RIGHT DOOR IS SHOWN;NOTE:
THE UPPER RIGHT DOOR AND THE A
LOWER AND UPPER LEFT DOOR WEAR LIMITS ARE THE SAME.
1
THE BODY LUG IS BUSHED; THE DOOR LUGS ARE NOT.
Horizontal Stabilizer Body Seal Door Wear Limits Figure 601 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-41-14
ALL ú ú 01 Page 603 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
DRIVE FITTING
4. ROD END/ TEFLON LINER
3. BOLT/BEARING
Horizontal Stabilizer Body Seal Door Wear Limits
Figure 601 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-41-14
ALL ú ú 01 Page 604 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
PIVOT
CRANK
DBD
B
SEE A
C C STABILIZER A
A
ACCESS CONTROL ROD SLIDING BLADE
CONTROL MAST SEAL (HIGHER)
ROD UPPER SEAL DOOR (RETRACTED)
STABILIZER CENTER SECTION
FWD (TOP SURFACE)
NOTE:THE UPPER RIGHT DOOR IS SHOWN; THE LOWER RIGHT DOOR AND THE UPPER AND LOWER LEFT DOOR WEAR LIMITS ARE THE SAME.
A
ATTACHMENT CRANK
1. SHAFT/BUSHING PIVOTFITTING
(2 LOCATIONS) 5. ROD END/ TEFLON LINER
ROD END
4. BOLT/BEARING
3. BOLT/BUSHING (2 LOCATIONS)
2. PIVOT/BUSHINGCRANK (2 LOCATIONS)
A-A B-B
CRANK 4. BOLT/BEARING ROD END ROD END
4. BOLT/BEARING
MAST
7. BOLT/MAST
5.
ROD END/
6.
BOLT/CRANK 5. ROD END/
TEFLON LINER
TEFLON LINER
C-C D-D
Horizontal Stabilizer Body Seal Door Mechanism Wear Limits
Figure 602 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-41-14
ALL ú ú 01 Page 605 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：747-400 AMM 飞机维护手册 飞行操纵 FLIGHT CONTROLS 4(17)
