S 865-039
(3)
Turn the shutoff valve handle to the fully closed position.
S 865-040
(4)
Install the rig pin and install the DO NOT OPEN tag.
S 485-008
(5)
Use the strut inflation tool or the manifold assembly to connect the pressurized source of clean dry air or nitrogen to the air charging valve.
S 865-010
(6)
Slowly increase the pressure and then stop when the pressure is 100 psi (690 kPa) more than the INCR: BY pressure on the switch nameplate.
(a)
Make sure that there are no leaks in the switch and manifold assembly.
(7)
Remove the rig pin and remove the DO NOT OPEN tag.
S 095-015
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-48-03
ALL ú ú 01 Page 506 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
(8) S 865-016Turn the shutoff valve handle counterclockwise to the fully open position.
(9) S 615-018Service the shock strut, if it is necessary (AMM 12-15-05/301).
S 095-021
(10)
Remove the strut inflation tool or the manifold assembly and the source of air or nitrogen.
S 085-022
(11)
Make sure you remove the landing gear ground locks (AMM 09-11-00/201).
S 095-020
WARNING: USE THE PROCEDURE IN AMM 32-00-30/201 TO REMOVE THE DOOR
_______ LOCKS FROM THE NOSE GEAR. THE DOORS OPEN AND CLOSE QUICKLY AND CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
(12) Do this task: "Removal of the Door Locks from the Nose Landing Gear" (AMM 32-00-30/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-48-03
ALL ú ú 01 Page 507 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 FAULT ISOLATION/MAINT MANUAL
FLAPS
COMPONENT SHT 102 FIG. QTY ACCESS/AREA REFERENCE
ACTUATOR - TRAILING EDGE FLAP, (M7985) 5 1 CONTROL INPUT LEVER ASSEMBLY L BODY GEAR WHEEL WELL, FLAP *
AFTFLAP - INBOARD 2 2 EXTEND FLAPS, INBD TE FLAPS 27-51-03
AFTFLAP - OUTBOARD 3 2 EXTEND FLAPS, OUTBD TE FLAPS 27-51-06
ASSEMBLY - FLAP CONTROL INPUT LEVER 5 1 L BODY GEAR WHEEL WELL 27-51-35
ASSEMBLY - INBD FLAP CONTROL 5 1 FLAP POWER PACKAGE L BODY GEAR WHEEL WELL, INBD 27-51-19
ASSEMBLY - FLAP CONTROL LEVER RVDT, M7885 6 1 FLT COMPT, FLAP CONTROL LEVER 27-51-07
ASSEMBLY - OUTBD FLAP CONTROL 5 1 FLAP POWER PACKAGE R BODY GEAR WHEEL WELL, OUTBD 27-51-19
BRAKE - NO COAST DRAG 5 1 L BODY GEAR WHEEL WELL 27-51-42
BOGIE - INBD FLAP FORWARD 3 4 EXTEND FLAPS, INBD TE FLAPS 27-51-43
CAM - INBD AFTFLAP DRIVE GENEVA 3 4 MECHANISM EXTEND FLAPS, INBD AFTFLAP DRIVE 27-51-39
CAM - OUTBD AFTFLAP DRIVE GENEVA 4 4 DRIVE MECHANISM EXTEND FLAPS, OUTBD AFTFLAP 27-51-40
CARRIAGE - INBD FLAP 3 4 FAIRING SUPPORT EXTEND FLAPS, INBD FLAP TRACK 27-51-23
CARRIAGE AND TOGGLE - INBD FOREFLAP 3 4 FAIRING SUPPORT EXTEND FLAPS, INBD FLAP TRACK 27-51-24
CARRIAGE - OUTBD FLAP 4 4 FAIRING SUPPORT EXTEND FLAPS, OUTBD FLAP TRACK 27-51-28
CARRIAGE - OUTBD FOREFLAP SEQUENCE 4 4 EXTEND FLAPS, OUTBD FLAP TRACK FAIRING SUPPORT 27-51-30
VALVE FLOW CONTROL CARTRIDGE - INBD FLAP CONTROL MODULE PRIORITY 5 1 FLAP POWER PACKAGE L BODY GEAR WHEEL WELL, INBD 27-51-10
PRIORITY VALVE FLOW CONTROL CARTRIDGE - OUTBD FLAP CONTROL MODULE 5 1 FLAP POWER PACKAGE R BODY GEAR WHEEL WELL, OUTBD 27-51-10
CIRCUIT BREAKERS - 6 FLT COMPT, P6
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：747-400 AMM 飞机维护手册 飞行操纵 FLIGHT CONTROLS 4(33)
