(27)
Remove the bolt from the forward hinge fitting (View C, Fig. 402).
S 034-026-C03
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù.
COWL/REVERSERS USED ON STRUTS WITH ú 78-31-01
VIBRATION ISOLATOR SUSPENSION AND ú CONFIG 3 WITH CROSS BEAMS ú C01 Page 414 (AIRPLANES POST-BOEING-SB 737-54-1036) ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
S 034-027-C03
(28) Remove the bolt from the center hinge fitting (View D, Fig. 402).
S 864-028-C03
CAUTION: MAKE SURE THE THRUST REVERSER HALF DOES NOT TOUCH THE ADJACENT
_______ STRUCTURES, EQUIPMENTS AND STANDS. MAKE SURE THE AFT EDGE OF THE THRUST REVERSER HALF DOES NOT TOUCH THE SEAL SEGMENTS OF THE PRIMARY SLEEVE ASSEMBLY. DAMAGE CAN OCCUR.
(29)
Slowly move the thrust reverser half away and down from the engine.
S 864-029-C03
(30)
Lower the thrust reverser half and attach it to the dolly (or the shipping container).
S 094-030-C03
(31)
Remove the sling and fittings unless you are going to install the same thrust reverser half again.
TASK 78-31-01-404-031-C03
3. Thrust Reverser Half Installation
_________________________________
A. Equipment
(1)
Block, Pulley - C71002-77
(2)
Boom, Thrust Reverser Handling - C71002-2
(3)
Dolly, Thrust Reverser - C78011-1,
Optional: C78002-1
(4)
Hoist Assembly - Fish Pole, F80039-1
(or equivalent)
(5)
Fitting, Bootstrap Hoist Attach (Inboard) -C71003-2
(6)
Fitting, Bootstrap Hoist Attach (Outboard) -C71003-3
(7)
Matting, Rubber - 2 pieces - each approximately
4 feet (1.2 meters) square
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù.
COWL/REVERSERS USED ON STRUTS WITH ú 78-31-01
VIBRATION ISOLATOR SUSPENSION AND ú CONFIG 3 WITH CROSS BEAMS ú C01 Page 415 (AIRPLANES POST-BOEING-SB 737-54-1036) ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
(8)
Pins, Attach, Hoist Fitting - C71003-104
(2 quantity)
(9)
Rod, Alignment C78015-1 (2 quantity)
(10)
Sling, Thrust Reverser - C78003
(11)
Wrench Set, Thrust Reverser Hinge - C78014
B. Consumable Materials
(1)
Adhesive, Synthetic Rubber Buna N - BMS 5-14
(AMM 70-10-01/201)
(2)
Clay, Modeling
(3)
Grease, Aircraft Ball and Roller Bearing -BMS 3-24 (AMM 70-10-01/201)
(4)
Primer - BMS 10-11, Type 1 (AMM 70-10-01/201)
C. References
(1)
AMM 24-22-00/201, Manual Control
(2)
AMM 29-15-00/201, Hydraulic System A, B and Standby
(3)
AMM 54-32-01/401, Forward Fairing
(4)
AMM 71-11-02/401, Fan Cowl Panels
(5)
AMM 78-31-00/201, Thrust Reverser System
(6)
AMM 78-31-05/401, Cascades
(7)
AMM 78-31-08/401, Fan Duct Cowl and Thrust Reverser Opening Actuator
(8)
AMM 78-31-09/401, Flap Seal Door Deflector
(9)
AMM 78-34-02/201, Feed Back Push-Pull Cables
D. Access
(1) Location Zones
101/102 Flight Compartment
506 No. 1 Engine
606 No. 2 Engine
E. Procedure
S 864-032-C03
WARNING: BE CAREFUL WHEN YOU REMOVE AND INSTALL THE THRUST REVERSER IN
_______ SUDDEN STRONG WINDS CONDITIONS. DO NOT USE THE HOLD-OPEN ROD TO HOLD THE COWLING IN THE OPEN POSITION IF THE WIND VELOCITY IS MORE THAN 60 KNOTS. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO THE EQUIPMENT.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 EXHAUST(80)
