(c)
Attach the base to the boom support.
(d)
Put the boom into the base.
(e)
Install the upper attach fittings of the sling, C78003, to the bushed clevis fittings on the upper bifurcation of the thrust reverser (View B, Fig. 403).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù.
COWL/REVERSERS USED ON STRUTS WITH ú 78-31-01
VIBRATION ISOLATOR SUSPENSION AND ú CONFIG 3 WITH CROSS BEAMS ú C03 Page 411 (AIRPLANES POST-BOEING-SB 737-54-1036) ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
BOOM
SEE A PULLEY BLOCK
FISHPOLE HOIST
SEE B
THRUST REVERSER SLING
SEE C
BOOM
BASE
BOOM ATTACH PIN SET
SUPPORT (2 LOCATIONS)
BOOTSTRAP HOIST ATTACH FITTING (2 LOCATIONS)
STRUT FITTING (2 LOCATIONS)
A
Thrust Reverser Handling Equipment Figure 403 (Sheet 1)
E69165
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù.
COWL/REVERSERS USED ON STRUTS WITH ú 78-31-01
VIBRATION ISOLATOR SUSPENSION AND ú CONFIG 3
WITH CROSS BEAMS ú C01 Page 412
(AIRPLANES POST-BOEING-SB 737-54-1036) ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
CLEVIS CONNECTED TO BUSHED UPPER ATTACH FITTINGS
BLOCK PULLEY
A
A SLING CLEVIS BUSHED REVERSER HINGE FORWARD THRUST
REVERSER HINGE CENTER THRUST
B CLEVIS BUSHED
UPPER BIFURCATION A-A
SLING LOWER ATTACH FITTINGS
C
Thrust Reverser Handling Equipment Figure 403 (Sheet 2)
E69166
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù.
COWL/REVERSERS USED ON STRUTS WITH ú 78-31-01
VIBRATION ISOLATOR SUSPENSION AND ú CONFIG 3
WITH CROSS BEAMS ú C01 Page 413
(AIRPLANES POST-BOEING-SB 737-54-1036) ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
(f)
Install the lower attach fittings of the sling, C78003, at the tapped holes in the lower bifurcation (View C, Fig. 403).
(g)
Attach the fishpole hoist and pulley block to the sling.
NOTE: Use the upper attach point on the sling if you remove
____ the inboard thrust reverser half. Use the lower attach point on the sling if you remove the outboard thrust reverser half.
(h) Use the fishpole hoist to lift up the sling and attach the
sling to the upper and lower attach fittings.
S 494-024-C03
(25) If the overhead handling equipment for the thrust reverser is to be used, install the equipment as follows (View B and C, Fig. 403):
(a)
Install the upper attach fittings of the thrust reverser sling, C78003, to the bushed clevis fittings on the upper bifurcation of the the thrust reverser (View B, Fig. 403).
(b)
Install the lower attach fittings of the thrust reverser sling, C78003, at the tapped holes of the lower bifurcation (View C, Fig. 403).
(c)
Attach the overhead hoist to the thrust reverser sling, C78003.
NOTE: Use the upper attach point on the sling if you remove
____ the inboard thrust reverser half. Use the lower attach point on the sling if you remove the outboard thrust reverser half.
(d) Use the overhead hoist to lift up the sling and attach the
sling to the upper and lower attach fittings.
S 034-025-C03
(26)
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 EXHAUST(79)
