S 014-003-C01
(2)
Remove hydraulic power (AMM 29-15-00/201).
S 014-002-C01
(3)
Remove the pressure from the applicable hydraulic reservoir (AMM 29-09-00/201).
S 044-086-C01
(4)
Open the circuit breakers and attach the DO-NOT-CLOSE tags for the applicable engine:
(a) P6 Load Control Center
1) ENG 1 THR REV IND SYS
2) ENG 2 THR REV IND SYS
3) ENG 1 SYNC LOCK
ENG 2 SYNC LOCK
ENG 2 SYNC LOCK - ALTN
S 014-087-C01
(5)
Remove the fan cowl panel (AMM 71-11-02/401).
(6)
Remove the forward segment of the reverser sleeve-to-strut fairing.
(7)
Remove the forward fairing (AMM 54-32-01/401).
(8)
Manually extend the thrust reverser (AMM 78-31-00/201).
(9)
Remove the forward two hinge fitting seal supports (Fig. 401).
(10)
Manually retract the thrust reverser (AMM 78-31-00/201).
S 034-005-C01
S 034-006-C01
S 014-007-C01
S 034-008-C01
S 014-009-C01
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù.
COWL/REVERSERS USED ON STRUTS WITHOUT ú 78-31-01
VIBRATION ISOLATOR SUSPENSION ú CONFIG 1 ú C02 Page 402 ú Mar 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
S 434-010-C01
(11)
Put the protective mat on the top surface of the sleeve and attach the mat to the sleeve with tape.
S 434-011-C01
(12)
If you remove an inboard thrust reverser half, wrap a protective mat around the wing leading edge adjacent to the thrust reverser half.
S 434-012-C01
(13)
Attach the mat to the leading edge with tape.
SLEEVEHINGE FITTING SEAL SUPPORTS
THRUST REVERSER SLEEVE-TO-STRUT FAIRING
SEE A
FWD
A
Thrust Reverser Hinge Fitting Seal Support Installation
Figure 401
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù.
COWL/REVERSERS USED ON STRUTS WITHOUT ú 78-31-01
VIBRATION ISOLATOR SUSPENSION ú CONFIG 1 ú C01 Page 403 ú Mar 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
S 014-000-C01
WARNING: OBEY THE INSTRUCTIONS IN AMM 78-31-00/201 TO OPEN THE THRUST
_______ REVERSERS. IF YOU DO NOT OBEY THE INSTRUCTIONS, INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT CAN OCCUR.
(14)
Open the thrust reverser (AMM 78-31-00/201).
S 034-015-C01
(15)
Remove these items at the aft hinge fitting (View E, Fig. 402) as follows:
NOTE: Keep the forward and aft halves of the slider together as a
____ set. The slider halves must be examined for wear before you install them again. The minimum distance between the curved surfaces of the hinge slider is 0.978 inch (24.84 mm).
NOTE: If you install the same thrust reverser again, measure
____ the distance between the inner curved surfaces of the hinge track fitting. The maximum permitted distance between the curved surfaces is 1.067 inches (27.10 mm), (Fig. 402, sheet 5). The maximum permitted gap between the hinge slider and the hinge track is 0.067 inch (1.70 mm).
(a)
Remove the forward half of the slider.
(b)
Remove the aft half of the slider with the eccentric pins
attached.
S 954-016-C01
(16) Apply masking tape along the seal segments of the primary sleeve assembly.
S 414-017-C01
CAUTION: MAKE SURE THERE IS PROPER CLEARANCE BETWEEN THE THRUST REVERSER
_______ AND THE SEAL SEGMENTS OF THE PRIMARY SLEEVE ASSEMBLY WHEN YOU CLOSE THE THRUST REVERSER HALF. DAMAGE TO EQUIPMENT CAN OCCUR.
OBEY THE INSTRUCTIONS IN THE PROCEDURE TO CLOSE THE THRUST REVERSERS. IF YOU DO NOT OBEY THE INSTRUCTIONS, INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT CAN OCCUR.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 EXHAUST(53)
