737-300 400 500 AMM 飞机维护手册 EXHAUST(52)

曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

 2) If any part of the seal or fairing is gone or damaged, ú replace the seal and repair the bullnose fairing per ú SRM 54-30-02/101.
 S 216-027-C00
 (23)
 Make sure that the 8 "C" duct drains by the thrust reverser latches are not clogged (Fig. 601).

 S 416-040-C00

 (24)
 Close the fan cowl panels (AMM 71-11-02/201).

 S 446-025-C00

 (25)
 Do the activation procedure for the thrust reverser (AMM 78-31-00/201).

 S 716-008-C00

 (26)
 Use the Power procedure to move the thrust reverser to the extended position (AMM 78-31-00/201).

 (a)  
Make sure the two sleeves move to the extended position at the same time and that they move smoothly.

 (b)  
Listen for unusual or too much noise from the rotating flex shafts.

 

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 78-31-00
 ALL  ú ú C01.1 Page 625 ú Jul 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
S 716-009-C00
 (27) Use the Power procedure to move the thrust reversers to the retracted position (AMM 78-31-00/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 78-31-00
 ALL  ú ú C01 Page 626 ú Mar 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
THRUST REVERSER - REMOVAL/INSTALLATION
______________________________________
 1.  General
_______
 A.  This procedure removes and installs the left or right thrust reverser half on the left or right engine.
 TASK 78-31-01-004-001-C01
 2.  Thrust Reverser Half Removal
____________________________
 A.  Equipment
 (1)  
Block, Pulley - C71002-77

 (2)  
Boom, Thrust Reverser Handling - C71002-2

 (3)  
Dolly, Thrust Reverser - C78011-1 or Optional: C78002-1

 (4)  
Hoist Assembly - Fish Pole, F80039-1
 (or equivalent)

 (5)  
Fitting, Bootstrap Hoist Attach (Inboard) -C71003-2

 (6)  
Fitting, Bootstrap Hoist Attach (Outboard) -C71003-3

 (7)  
Matting, Rubber - 2 pieces - each approximately
 4 feet (1.2 meters) square

 (8)  
Pins, Attach, Hoist Fitting - C71003-104
 (2 quantity)

 (9)  
Sling, Thrust Reverser - C78003

 (10)
 Wrench Set, Thrust Reverser Hinge - C78014

 B.  
References

 (1)  
AMM 54-32-01/401, Forward Fairing

 (2)  
AMM 71-11-02/401, Fan Cowl Panels

 (3)  
AMM 78-31-00/201, Thrust Reverser System

 C.  
Access

 (1)  
Location Zones
 101/102 Flight Compartment
 506 No. 1 Engine
 606 No. 2 Engine

 D.  
Procedure

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù.
 COWL/REVERSERS USED ON STRUTS WITHOUT  ú 78-31-01
 VIBRATION ISOLATOR SUSPENSION  ú CONFIG 1 ú C01 Page 401 ú Mar 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
S 044-002-C01
 WARNING: BE CAREFUL WHEN YOU REMOVE AND INSTALL THE THRUST REVERSER IN
_______ SUDDEN STRONG WINDS CONDITIONS. DO NOT USE THE HOLD-OPEN ROD TO HOLD THE COWLING IN THE OPEN POSITION IF THE WIND VELOCITY IS MORE THAN 60 KNOTS. INJURY CAN OCCUR.
 DO THE DEACTIVATION PROCEDURE TO PREVENT THE OPERATION OF THE THRUST REVERSER. THE ACCIDENTAL OPERATION OF THE THRUST REVERSER CAN CAUSE INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT.
　
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 EXHAUST(52)