NOTE: You must compress the actuator rod to align the actuator rod
____ end with the fitting. You can turn the thrust reverser in an open direction when it is necessary to align it. Apply the opening force near the forward end of the lower bifurcation to prevent the thrust reverser to move at an angle.
S 014-032-C01
WARNING: OBEY THE INSTRUCTIONS IN AMM 78-31-00/201 TO OPEN THE THRUST
_______ REVERSERS. IF YOU DO NOT OBEY THE INSTRUCTIONS, INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT CAN OCCUR.
(23)
Open the thrust reverser (AMM 78-31-00/201).
S 434-054-C01
(24)
Install the hinge slider at the aft hinge fitting (View E, Fig. 402) as follows:
NOTE: Make sure the hinge slider halves and the hinge track fitting
____ are with in the permitted wear limits (Fig. 402, sheet 5). The distance between the curved surfaces of the hinge slider must not be less than 0.978 inch (24.84 mm). The distance between the inner curved surfaces of the hinge track fitting must not be more than 1.067 inches (27.10 mm). The maximum permitted gap between the hinge slider and the hinge track is
0.067 inch (1.70 mm).
(a) If necessary, assemble the slider aft half and the two
eccentric pins with nuts and washers.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù.
COWL/REVERSERS USED ON STRUTS WITHOUT ú 78-31-01
VIBRATION ISOLATOR SUSPENSION ú CONFIG 1 ú C01 Page 418 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
(b)
Make sure you install the eccentric lobes on the eccentric pins (Detail E, Fig. 402) as follows: 1) The top lobe must point to the 3 o'clock position. 2) The bottom lobe must point to the 9 o'clock position.
(c)
Install this assembly through the hinge fitting from the aft
side.
(d)
Install the slider forward half and install the nuts and washers (with the recessed side of the washer toward the slider half).
(e)
Tighten the nuts finger-tight.
(f)
Make sure that the forward and aft slider halves are positioned outboard, away from the strut centerline.
(g)
Use the slot to turn the two eccentric pins until the sliders touch the worn areas on the hinge track insert of the reverser.
(h)
Monitor the slider position during the closure of the thrust
reverser as follows:
1) A light shift of the sliders is usual.
2) Make sure that no binding occurs.
3) If binding is apparent, stop the closure and adjust the
sliders inboard.
WARNING: OBEY THE INSTRUCTIONS IN AMM 78-31-00/201 TO OPEN THE
_______
THRUST REVERSERS. IF YOU DO NOT OBEY THE INSTRUCTIONS,
INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT CAN OCCUR.
(i) Close and open the thrust reverser (AMM 78-31-00/201).
NOTE: The above close and open sequence makes sure that you
____
install the sliders correctly.
(j)
Apply the torque to the two nuts to connect the slider forward half to the aft hinge fitting.
(k)
Make sure the slider does not move while you tighten the nuts.
(l)
Remove the tape from the seal segments of the turbine exhaust sleeve.
S 034-055-C01
(25)
Remove the shim installed between the hinge link and forward hinge fitting (View C, Fig. 402).
S 434-090-C01
(26)
Connect the electrical connector D1008 (D1016) to the sync lock (View B, Fig. 402).
NOTE: If the replacement thrust reverser does not have the
____
sync lock installed, refer to SB 78-1053.
(a)
Install the lacing tape to tie the sync lock wiring harness to the thrust reverser wiring harness.
(b)
Install the sync lock wiring harness (W1412) through the clamps that are attached to the thrust reverser.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù.
COWL/REVERSERS USED ON STRUTS WITHOUT ú 78-31-01
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 EXHAUST(59)
