a) FLIGHT RECORDER AC
b) FLIGHT RECORDER DC
(r)
If the FLIGHT RECORDER light does not operate correctly, do a check of the flight recorder system (AMM 31-24-00/501).
(s)
Connect the CSD (AMM 24-11-11/501 [CSD disconnect test]).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
71-00-00
ALL ú ú C11 Page 576 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
TEST NO. 11 - T2/CIT SENSOR TEST
________________________________
TASK 71-00-00-815-022-C00
12. Test No. 11 - T2/CIT Sensor Test________________________________
A. General
(1)
This test gives the data to do troubleshooting of the T2 or CIT sensor for incorrect operation.
(2)
For the test, you use the ambient air temperature, operate the engine at low idle, and read the pressure differentials across the T2 and CIT sensors.
(3)
The condition of the sensors is found when you compare the measured pressure differentials to the usual pressure differentials for the air temperature.
B.
Equipment
(1)
FIT/CIT Sensor Tester - 856A1357G03,
CFM International, P.O. Box 15514,
Cincinnati, OH 45215
(2)
Alcohol Thermometer - MIL-T-11399, Type ML-5
(or mercury thermometer, if not taken aboard
airplane), -40° to 120°F (-40° to 49°C),
|1/2°F (|1/4°C) accuracy.
C.
Consumable Materials
(1)
Cable Tie Wraps
D.
References
(1)
AMM 71-00-00/201, Power Plant
(2)
AMM 71-00-00/501, Power Plant
(3)
AMM 71-11-02/201, Fan Cowl Panels
(4)
AMM 73-21-02/401, Compressor Inlet Temperature Sensor
(5)
AMM 73-21-09/401, T2 Temperature Sensor
E.
Access
(1)
Location Zones
506 Engine No. 1
606 Engine No. 2
(2)
Access Panels
5737L/5837R Fan Cowl Assy
5746L/5846R Fan Cowl Assy
F.
Procedure
(1)
Open the left fan cowl panel (AMM 71-11-02/201).
S 485-024-C00
(2)
Install the FIT/CIT Sensor Tester as follows:
(a)
Find a good location on the engine (fan frame or TGB) for the tester mounting plate.
(b)
Secure the gage assembly to the engine with cable tie wraps in the four holes of the corners of the frame.
S 015-023-C00
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
71-00-00
ALL ú ú C12 Page 577 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
TEST NO. 11 - T2/CIT SENSOR TEST
________________________________
(c) Install the PB T-fitting as follows: 1) Find the PB port on the MEC. 2) Disconnect the first coupling where the metal tube connects
with the flexible hose. 3) Install the PB T-fitting in the PB line. a) Tighten the coupling nuts to 135-150 pound-inches (15-17 N.m).
4) Install the line from the PB T-fitting to the port identified PB on the gage assembly. a) Tighten the coupling nuts to 135-150 pound-inches
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 动力装置 POWER PLANT 1(80)
