MEC
PREFORMED
PACKING
WASHER
(2 LOCATIONS)
SCREW
(2 LOCATIONS)
B
Specific Gravity, Low Idle and High Idle, and Power Trim Adjustments
Figure 502
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
71-00-00
ALL ú ú C01 Page 522 ú Jul 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
Not Used
Figure 503
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
71-00-00
ALL ú ú C01 Page 523 ú Jul 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
H56346
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
Not Used
Figure 504
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
71-00-00
ALL ú ú C01 Page 524 ú Jul 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
H56363
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
Not Used
Figure 505
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
71-00-00
ALL ú ú C01 Page 525 ú Jul 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
H56364
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
Not Used
Figure 506
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
71-00-00
ALL ú ú C01 Page 526 ú Jul 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
H56367
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
TEST NO. 4 - IDLE SPEED CHECK
_____________________________
5) See that the applicable FUEL VALVE CLOSED light on the pilots' overhead panel, P5, is dim.
NOTE: This shows that the valve is closed.
____
6) Open the applicable SHUTOFF VALVE ENG circuit breaker on the circuit breaker panel, P6, and install the DO-NOT-CLOSE tag.
7) Open the left fan cowl panel (AMM 71-11-02/201).
8) Put the container below the low idle adjustment to catch the fuel that drains from the MEC port.
9) Use a 9/64 inch hexagonal wrench to remove the screws and washers that attach the low idle adjustment. a) Remove the assembly from the MEC port
(Fig. 502, View B). b) Remove and discard the packing. 10) Compare the %N2 rpm record and the high idle trim target for the current OAT and barometric pressure.
11) Find the adjustment that is necessary to get the %N2 rpm limits as follows: a) Use a 3/32 inch x 3 inch hexagonal wrench to carefully
engage the high idle adjustment (through the port that
you opened by the removal of the low idle adjustment).
b) Turn the high idle trim screw clockwise to increase the rpm or counterclockwise to decrease the rpm (one full turn causes approximately 5% change in the N2 rpm).
c) Set the %N2 rpm in the limits.
12) Use a new packing to install the low idle adjustment in the MEC port. a) Install the two washers and screws. b) Tighten the screws to 19-22 pound-inches
(2.1-2.5 newton-meters).
13) Close the fan cowl panel (AMM 71-11-02/201).
14) Remove the DO-NOT-CLOSE tag from the SHUTOFF VALVE ENG
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 动力装置 POWER PLANT 1(54)
