(2)
This procedure can be used to make a check of the engine operation or related systems when engine operation is necessary.
(3)
During cold weather, additional procedures such as preheating may be necessary.
(4)
These ground start procedures are authorized for two successive attempts to start the engine. Do not operate the starter more than the limits.
(a)
If the engine fails to start after the second attempt, do the steps that follow: 1) Dry motor for an additional two minutes, then shut down the
engine. 2) Do this procedure, Power Plant - Trouble Shooting (Starting And Idle) (AMM 71-00-41/101).
(5)
The starter air discharge duct fitting and forward drain hole should be observed during starting for signs of too much leakage
(6)
Indication readings should be done while you observe pointers during transient operation and digitals during stable operation.
(7)
It is important to have a clean engine compartment because the large quantity of airflow can pull unwanted material into the engine.
(a)
You must fully clean and examine the area after you are done with the work.
(b)
Make sure there is no dirt, oil or grease in the inlet area.
(8)
In order to prevent corrosion in the compressor stages and damage to the fan, it is recommended that you install the engine inlet and exhaust covers when it is possible.
(9)
When there is freezing precipitation or sufficient wind to turn the engine it is important to immediately install the covers on the engine.
B.
Equipment
(1)
Service Interphone Equipment
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
71-00-00
ALL ú ú C03 Page 244 ú Mar 15/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
(2) Engine Inlet and Exhaust Covers -C10001-1 and C10001-2 are superseded by commercial equipment as follows:
Langdon Manufacturing Co., 222 N. Hydraulic, P.O. Box 11026, Wichita, KS 67202
-Inlet cover part No. LMC11G84-1
-Exhaust cover part No. LMC11G84-2,
or
Texstar Plastics,
802 Ave J East, P.O. Box 534036,
Grand Prairie, TX 75051
-Inlet cover part No. 5101505
-Exhaust cover part No. 5101504
(3) Safety Lanyard - Personnel,
Engine Maintenance, F80239
NOTE: Use of the safety lanyard is
____
recommended.
(4) Inlet Barrier - Personnel, Plug-In, C71013 (alternate to inlet guard C12001)
NOTE: Use of inlet barrier is recommended.
____
(5) Inlet Guard - Engine Run-Up, C12001 (alternate to inlet barrier C71013)
NOTE: Use of inlet guard is recommended.
____
C. References
(1)
12-11-00/301, Fuel Servicing
(2)
12-12-00/301, Hydraulic Servicing
(3)
12-13-11/301, Engine Oil
(4)
12-13-21/301, Constant Speed Drive
(5)
24-22-00/201, Manual Control
(6)
36-05-00/201, Pneumatic System
(7)
71-00-00/501, Power Plant
(8)
71-00-01/201, Power Plant
(9)
71-11-02/201, Fan Cowl Panels
(10)
78-31-00/201, Thrust Reverser System
D.
Access
(1)
Location Zones
506 Engine No. 1
606 Engine No. 2
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
71-00-00
ALL ú ú C03 Page 245 ú Mar 15/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
(2)
Access Panels
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 动力装置 POWER PLANT 1(27)
