747-400 AMM 飞机维护手册 飞行操纵 FLIGHT CONTROLS 3(27)

曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

 8)  Remove the dial indicator.
Do a check of the outboard elevator freeplay:
 1)  Mount the dial indicator 1 inch from the trailing edge at the inboard end of the elevator.
 CAUTION: USE SUFFICIENT PADDING ON THE THE FORCE SCALE TO
_______ PREVENT DAMAGE TO THE ELEVATOR SURFACES.
 2)  Apply an up force of 15 pounds at about 11 inches from the the elevator trailing edge and at a point on the elevator rib opposite the pressurized PCA being tested.
 NOTE: For padding, you can use a wood block of
____
 5 X 5 X 0.25 inch.

 3) Set the dial indicator to zero while you apply the force. 4) Slowly release the 15 pounds force.
 CAUTION: USE SUFFICIENT PADDING ON THE THE FORCE SCALE TO
_______ PREVENT DAMAGE TO THE ELEVATOR SURFACES.
 5)  Apply a down force of 10 +/- 2 pounds at about 11 inches from the elevator trailing edge and at a point on the elevator rib opposite the pressurized PCA being tested.
 NOTE: For padding, you can use a wood block of
____
 5 X 5 X 0.25 inch.

 6) Slowly release the 10 +/- 2 pounds force.
 7) Make sure the dial indicator reading is not greater that

 0.15 inches. 8) Remove the dial indicator.Remove the rigging pin E-2.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-31-00
 ALL  ú ú 01 Page 530 ú Jun 10/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 735-114
 (7)  
Do the High Column Feel Force Check:

 (a)  
Set the horizontal stabilizer to a B dimension of 7.37-7.47 inches.

 WARNING: KEEP PERSONS AND EQUIPMENT AWAY FROM ALL CONTROL SURFACES
_______ WHEN HYDRAULIC POWER IS SUPPLIED. AILERONS, ELEVATORS, RUDDER, FLAPS, SLATS, SPOILERS, AND STABILIZER ARE FULLY POWERED SURFACES. INJURY TO PERSON OR DAMAGE TO EQUIPMENT CAN OCCUR WHEN HYDRAULIC POWER IS SUPPLIED.
 (b)  
Supply system No. 2 and 3 hydraulic power (AMM 29-11-00/201).

 (c)  
Install rig pin E1 in crank at the left end of the control column torque tube to make sure the column is in neutral position.

 (d)  
Make sure that you can install rig pin E2 at the base of the aft quadrant.

 (e)  
Make sure that control rod which connects the feel unit input crank to the aft quadrant is in the mid-adjustment position.

 (f)  
Disconnect all output rods from the aft quadrant.

 1)  Move the captain's or firt officer's control column from the center detent slowly to the 5/6 full aft position (approximately 10 degrees).
 2)  Make sure that the force to move the control column is approximately 4.0 pounds. 3) Release the control column.
 (g)  Re-connect the feel unit control rod to the aft quadrant. 1) Do this task: Elevator Feel Unit - Operational Test (AMM 27-31-17/201). 2) Depressurize system No. 2 and 3 hydraulic power
 (AMM 29-11-00/201). 3) Depressurize auxiliary pitot systems No. 1 and 2. 4) Move the captain's or first officer's control column from
 center detent slowly to the 5/6 full aft position (approximately 10 degrees). 5) Make sure that the force to move the control column is approximately 20 to 33 pounds. 6) Release the control column.
 (h) Re-connect the left inboard PCU linkage to the aft quadrant.
 1)  Move the captain's or first officer's control column from center detent slowly to the 5/6 full aft position (approximately 10 degrees).
 2)  Make sure that the force to move the control column is approximately 20 to 33 degrees.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-31-00
 ALL  ú ú 01 Page 531 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
 (i)

A
747-400
MAINTENANCE MANUAL

 WARNING:_______ KEEP PERSONS AND EQUIPMENT AWAY FROM ALL CONTROL
 SURFACES WHEN HYDRAULIC POWER IS SUPPLIED.  AILERONS,
 ELEVATORS, RUDDER, FLAPS, SLATS, SPOILERS, AND
 STABILIZER ARE FULLY POWERED SURFACES.  INJURY TO
 PERSON OR DAMAGE TO EQUIPMENT CAN OCCUR WHEN

 HYDRAULIC POWER IS SUPPLIED.
　
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：747-400 AMM 飞机维护手册 飞行操纵 FLIGHT CONTROLS 3(27)