27-81-00
ALL ú ú 02 Page 557 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
(c) If you cannot get a clearance of 0.0 to 0.06 inch at the slat ends, adjust as follows: 1) Remove up to 0.04 inch maximum thickness from the laminated
shims under the forward lower auxiliary track clevis to bring the slat ends to 0.0 to 0.06 inch.
NOTE: If you removed the shims, it is possible that
____ the slats will not fall correctly into detent in the extend or retract cycle. If this occurs, you must reinstall the laminated shims as necessary to permit the detents to operate correctly.
S 085-204
(40) Remove the leading edge slat actuator locks from the leading edge slat (AMM 27-81-00/201).
S 495-205
WARNING:_______CAREFULLY INSTALL THE LEADING EDGE SLAT ACTUATOR LOCKS. THE LEADING EDGE SLATS CAN MOVE QUICKLY IF YOU DO NOT INSTALL THE LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
(41)
Install the leading edge slat actuator locks when you adjust the leading edge slats with the actuator connected (AMM 27-81-00/201).
(a)
Make sure the clearance between the slat upper trailing edge to fixed leading edge is 0.002 to 0.008 inch .
NOTE: Measure the clearance at the highest point, within 8.0
____ to 9.0 band that is centered about the auxiliary track centerline. Measure the clearance to a depth of 0.4 to
0.6 inch with a feeler gage.
(b)
If the clearance is not 0.002 to 0.008 inch, then do these steps to adjust the aft lower auxiliary track support: 1) Adjust the aft lower auxiliary track support until the
clearance between the slat upper trailing edge to fixed leading edge is 0.002 to 0.008 inch.
(c)
Make sure the clearance between the slat upper trailing edge and the fixed leading edge is 0.0 to 0.0600 inch at the slat ends.
NOTE: Measure the clearance at 0.75 to 1.0 inch from the
____ inboard and outboard end of the slats.
1) If you cannot get a clearance of 0.0 to 0.06 inch at the slat ends, adjust as follows: a) Turn the adjustment nut of each aft lower auxiliary
track an additional maximum one (1) turn.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-81-00
ALL ú ú 02 Page 558 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
S 285-268
(42) Do these checks on the detent arm and adjust the detent arms again if it is necessary (Fig. 506):
(a) Move the flap control lever to the 1-unit detent to extend the
leading edge slats to the intermediate position.
NOTE: Remove and install slat actuator locks and obey safety____
warnings to prevent injury to persons or damage to
equipment.
(b) Make sure that the detent arm roller touches the bottom of the
cam plate.
(c) Make sure there is a distance of 0.00 to 0.03 inch between the
cam plate and the forward surface of the detent arm roller.
(d) If it is necessary, adjust the detent arm torsion to a load of
50 pounds (22.68 Kgms) +/-5 pounds (2.268 Kgms) at the
auxiliary track locations with the steps that follow:
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 飞行操纵 FLIGHT CONTROLS 6(51)
