(2)
27-51-32/401, Inboard Flap Track Fairing
B.
Access
(1)
Location Zone 216, 217 Main Wheel Well 307, 407 Wing Trailing Edge Outboard Flap and Spoilers 309, 409 Wing Trailing Edge Inboard Flap and Spoilers
C.
Procedure
S 014-002
(1)
Remove the inboard flap track fairing if it is necessary to get access to the torque tube (Ref 27-51-32/401).
(2)
Pressurize the hydraulic system B (Ref 27-51-00/201).
S 864-004
(3)
Move the flap control lever to the 40-unit detent to extend the flaps.
(4)
Release the pressure in the hydraulic system B (Ref 27-51-00/201).
S 494-006
(5)
Install a support to hold the flap while the torque tubes are disconnected.
S 864-003
S 864-005
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-64
ALL ú ú 01 Page 401 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 014-007
(6)
If you will remove a torque tube in the wing, remove the torque tube guard.
S 024-008
(7)
Remove the torque tube:
(a)
Remove the three screws that attach the coupling sleeves to the spline coupling.
(b)
Move the coupling sleeves off the coupling to disconnect the torque tubes.
(c)
If the torque tube is between the inboard flap transmission and the angle gearbox, disconnect the two parts of the torque tube: 1) Disconnect the three bolts, washers and nuts at the flange
connection.
(d)
Remove the torque tube from the airplane.
TORQUE TUBE
COUPLING SLEEVESEE A
SPLINE COUPLING HALF (ATTACHED TO POWER UNIT, GEARBOX OR TRANSMISSION)
(EXAMPLE) A
Example Torque Tube Installation Figure 401
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-64
ALL ú ú 01 Page 402 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
TASK 27-51-64-404-009
3. Flap Torque Tube Installation (Fig. 401)_____________________________
A. Consumable Materials
(1)
A00247 Sealant BMS 5-95
(2)
D00633 Grease - BMS 3-33 (Recommended)
(3)
D00013 Grease - MIL-G-23827 (Alternate)
B.
References
(1)
27-51-00/201, Trailing Edge Flap System
(2)
27-51-32/401, Inboard Flap Track Fairing
C.
Access
(1)
Location Zone 216, 217 Main Wheel Well 307, 407 Wing Trailing Edge Outboard Flap and Spoilers 309, 409 Wing Trailing Edge Inboard Flap and Spoilers
D.
Procedure
S 424-010
(1)
Install the flap torque tube:
(a)
Put the torque tube in its position in the airplane.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址:737-300 400 500 AMM 飞机维护手册 飞行操纵 FLIGHT CONTROLS 4(98)