27-51-34
ALL ú ú 01 Page 802 ú Jul 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
FOREFLAP
FOREFLAP PUSHROD
SHEAR RIVET
EXHAUST GATE
(AIRPLANES WITH TWO PUSHRODS) B
FOREFLAP
FOREFLAP PUSHROD
SHEAR RIVET EXHAUST GATE
(AIRPLANES WITH THREE PUSHRODS) B
Outboard Flap Exhaust Gate Pushrods Repairs Figure 801 (Sheet 2)
EXHAUST GATE PUSHROD
MECHANISM PUSHROD
SHEAR RIVETS
(2 LOCATIONS)
EXHAUST GATE PUSHROD
K29806
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-34
ALL ú ú 01 Page 803 ú Jul 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
OUTBOARD TRAILING EDGE FLAP EXHAUST GATE - REMOVAL/INSTALLATION
_______________________________________________________________
1. General_______
A. There are two tasks in this procedure: There is a task for the removal and a task for the installation of the outboard trailing edge flap exhaust gate.
TASK 27-51-35-004-001
2. Outboard Trailing Edge Flap Exhaust Gate Removal (Fig. 401)________________________________________________
A. References
(1)
AMM 27-51-00/201, Trailing Edge Flap Systems
B.
Access
(1)
Location Zone 101, 102 Control Cabin 307, 407 Wing Trailing Edge Outboard Flap and Spoilers
C.
Prepare for the Removal
S 864-002
(1)
Do this task: "Supply Hydraulic Power" (AMM 27-51-00/201).
S 864-003
(2)
Put the flap control lever in the 40-unit detent to extend the flaps.
S 864-006
(3)
Do this task: "Remove Hydraulic Power" (AMM 27-51-00/201).
D.
Remove the Outboard Trailing Edge Flap Exhaust Gate
S 014-036
WARNING:_______MAKE SURE YOU HOLD THE EXHAUST GATE IN ITS POSITION. THE EXHAUST GATE CAN FALL TO THE FULL EXTEND POSITION. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
(1)
AIRPLANES WITH THREE PUSHRODS; Disconnect the exhaust gate rod assembly from the exhaust gate:
(a)
Remove the cotter pin, nut, washer and bolt from the exhaust gate rod assembly.
S 014-037
(2)
AIRPLANES WITH TWO PUSHRODS; Disconnect the exhaust gate rod assembly from the exhaust gate:
(a)
Remove the nut, washer and bolt from the exhaust gate rod assembly.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-35
ALL ú ú 01 Page 401 ú Jul 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500
MAINTENANCE MANUAL
SEE A
SEE A
MIDFLAP
AFTFLAP
FWD
EXHAUST GATE MECHANISM SEE B EXHAUST GATE FOREFLAP A (RIGHT FLAP OPPOSITE) LEFT FLAP INBD
Outboard Flap Exhaust Gate Installation Figure 401 (Sheet 1)
H48695
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-35
ALL ú ú 01 Page 402 ú Jul 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 024-040
(3)
AIRPLANES WITH THREE PUSHRODS;
Disconnect the exhaust gate assembly from the midflap:
(a)
Remove the exhaust gate mounting bolts, washers, nuts and cotter pins.
S 024-041
(4)
AIRPLANES WITH TWO PUSHRODS;
Disconnect the exhaust gate assembly from the midflap:
(a)
Remove the exhaust gate mounting bolts, washers, and nuts.
S 024-056
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址:737-300 400 500 AMM 飞机维护手册 飞行操纵 FLIGHT CONTROLS 4(56)