TASK 27-51-34-226-012-002
3. Outboard Trailing Edge Flap Exhaust Gate Actuation Mechanism Inspection
_______________________________________________________________________
A. Standard Tools and Equipment
(1)
Micrometer 0 to 1 inch
B.
References
(1)
AMM 27-51-34/401, Outboard Trailing Edge Flap
C.
Access
(1)
Access Panels
8215, 8715 Exhaust Gate Linkage Access Panel
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH TWO EXHAUST GATE ú
27-51-34
PUSHRODS. ú CONFIG 2 ú 02 Page 612 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
D. Procedure
S 016-013-002
(1)
Do this task: "Outboard Trailing Edge Flap Removal"
(AMM 27-51-34/401).
S 226-014-002
(2)
Measure the parts on the actuator mechanism for the exhaust gate (Fig. 602):
(a)
Remove the parts.
(b)
Use a micrometer to measure the parts.
(c)
Compare the dimensions you measured with the permitted dimensions shown in Fig. 602.
(d)
Replace the parts that are not in the tolerance.
(e)
Install the parts.
S 416-015-002
(3) Do this task: "Outboard Trailing Edge Flap Installation" (AMM 27-51-34/401).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH TWO EXHAUST GATE ú
27-51-34
PUSHRODS. ú CONFIG 2 ú 01 Page 613 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
EXHAUST GATE ACTUATOR PUSHRODS - REPAIRS
___________________________________________
1. General_______
A. There is one task in this procedure, a repair of the pushrods for the outboard exhaust gate actuator mechanism. The repair includes the replacement of the rivets that attach the pushrod to the rod end fitting.
TASK 27-51-34-308-001
2. Exhaust Gate Actuator Pushrod Repair (Fig. 801)____________________________________
A. Standard Tools and Equipment
(1)
Shear Rivets - BACR15BB4D9
(2)
Shear Rivets - BACR15BB5D10
B.
References
(1)
AMM 27-51-34/401, Inboard TE Flap
C.
Access
(1)
Location Zone 307, 407 Wing Trailing Edge Outboard Flap and Spoilers
D.
Procedure
S 028-002
(1)
Remove the pushrod for the exhaust gate actuator mechanism (AMM 27-51-34/401).
S 358-003
(2)
Repair the pushrod:
WARNING:_______DO NOT MAKE THE RIVET HOLES LARGER. YOU WILL CAUSE DAMAGE TO THE PUSHROD AND THE ROD END FITTING.
(a)
Remove the broken parts of the rivets from the holes in the pushrod.
(b)
Install the new rivets.
S 428-004
(3) Install the pushrod for the exhaust gate actuator mechanism (AMM 27-51-34/401).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-34
ALL ú ú 01 Page 801 ú Jul 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500
MAINTENANCE MANUAL
SEE A
SEE A
MIDFLAP
AFTFLAP
FWD
EXHAUST GATE MECHANISM SEE B EXHAUST GATE LEFT FLAP (RIGHT FLAP IS OPPOSITE) A FOREFLAP INBD
Outboard Flap Exhaust Gate Pushrods Repairs Figure 801 (Sheet 1)
K29802
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址:737-300 400 500 AMM 飞机维护手册 飞行操纵 FLIGHT CONTROLS 4(55)