(b)
Remove the cable guard from the flap control unit.
(c)
Remove the cables from the follow-up drum.
S 034-007
(6)
Remove the hydraulic lines from control valves for the leading edge and the trailing edge flaps.
(a)
Put a container below the flap control valves.
(b)
Disconnect the hydraulic lines.
(c)
Install caps in the ports and plugs in the hydraulic lines.
S 024-008
(7)
Remove the flap control unit:
(a)
Loosen the bolt input crank of the flap control unit.
(b)
Remove the three nuts and washers from the mounting studs for the control unit.
(c)
Remove the flap control unit from the airplane.
(d)
Install the cable guard, the switch cover, and the lower pan on the flap control unit.
TASK 27-51-74-404-009
3. Flap Control Unit Installation______________________________
A. Special Tools and Equipment
(1)
F80197-5 Wrench Set
B.
Standard Tools and Equipment
(1)
Rig Pin (F-1) - 0.311 +0.000/-0.002 inch diameter, 3.40 |0.06 inches long (MS20392-4)
NOTE: The rig pin is a part of the kit F70207-69, -78, or -83.
____
C. Consumable Materials
(1)
A00135 Sealant - BMS 5-19, Class A
(2)
C00259 Primer - BMS 10-11, Type I
(3)
C00308 Corrosion Preventive Compound - MIL-C-11796, Class 3
(4)
D00633 Grease - BMS 3-33 (Recommended)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-74
ALL ú ú 01 Page 404 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
D.
E.
F.
A
737-300/400/500MAINTENANCE MANUAL
(5)
D00013 Grease - MIL-G-23827 (Alternate)References
(1)
SWPM 20-20-00, Electrical Bonding
(2)
AMM 27-51-74/501, Flap Control UnitAccess
(1)
Location Zone
217 Right Main Wheel WellProcedure
S 014-010
(1)
Remove the lower pan, the switch cover and the cable guard from the flap control unit.
S 374-011
(2)
Apply a layer of the corrosion preventive compound to the control quadrant shaft and the splines of the input crank (Fig. 401).
S 394-012
(3)
Apply a layer of the sealant to the wheel well ceiling around the three mounting studs for the flap control unit.
S 494-013
(4)
Install the rig pin F-1 in the flap control unit.
S 424-014
(5)
Install the flap control unit:
(a)
Engage the input crank of the control unit and the quadrant shaft and put the flap control unit on the mounting studs.
NOTE: It is easier to align the splines if you move the slide
____
of the flap control valve.
(b)
Install the nuts and washers on the outboard mounting studs.
(c)
Attach the control unit to the inboard mounting stud: 1) Remove the finish from the lower surface of the mounting stud.
2) Put the washer and the bonding jumper on the mounting stud and install the washer and nut.
S 764-015
(6) Do this task to measure the bonding resistance between the control unit and the structure: "Electrical Bonding Check" (SWPM 20-20-00).
NOTE: The resistance must be less than 0.0025 ohms.
____
S 374-016
(7)
Apply a layer of the primer to the open area.
(8)
Tighten the bolt in the input crank of the flap control unit.
S 434-017
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-74
ALL ú ú 03 Page 405 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 飞行操纵 FLIGHT CONTROLS 4(128)
