737-300 400 500 AMM 飞机维护手册 飞行操纵 FLIGHT CONTROLS 4(85)

曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

 aft end of the tracks. b) Put a square on the straightedge to make the free leg of the square approximately vertical and point down.
 c)  Measure the distance between the square and the flat vertical side of the cam track, forward of the fasteners.
 NOTE: If the distance is more than 0.005 inch, Remove
____ or taper the laminations on the shims as required.
 4)  Tighten the fasteners that attach the cam track to the center fairing.
 5)  Make sure the distance between the fairing track and the cam track is 5.92-5.94 inches. a) Add or remove shims from the fairing tracks if the
 dimension is out of the tolerance. 6) Make sure the distance between the fairing tracks is 11.14-
11.16 inches.
 D.  Install the Center Fairing
 S 024-031
 (1)  
Install the center fairing:

 (a)  
Lift the center fairing to near its installed position.

 (b)  
Engage the bellcrank roller with the cam track of the aftflap drive mechanism.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-52
 ALL  ú ú 02 Page 407 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 (c)  
Engage the support arm rollers with the fairing tracks.

 (d)  
Move the center fairing forward and align the center fairing hinge fitting with the flap track fairing support.

 (e)  
Install the bushings and fasteners at the hinge fitting and the fairing support.

 S 434-032
 (2)  
At the outboard track center fairing, connect the landing light (Fig. 402):

 (a)  
Connect the rod end on the push/pull cable to the cam arm and the cam follower.

 (b)  
Engage the cam follower with the landing light cam track and install the cam track.

 (c)  
Connect the landing light electrical connector to the landing light.

 S 824-020
 (3)  
If you replaced the cam track of the aftflap drive mechanism, do a check of the track alignment:

 (a)  
Remove the aft fairing from the center fairing.

 NOTE: You can see the operation of the bellcrank with the aft
____
 fairing removed.

 WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF ALL
_______ CONTROL SURFACES BEFORE YOU SUPPLY HYDRAULIC POWER. AILERONS, RUDDERS, ELEVATORS, FLAPS, SPOILERS, LANDING GEAR, AND THRUST REVERSERS CAN MOVE QUICKLY WHEN YOU SUPPLY HYDRAULIC POWER. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (b) Do this task to pressurize hydraulic system B: "Pressurize Hydraulic System A, B, or Standby" (Ref 29-15-00/201).
 WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE
_______ TRAILING EDGE FLAPS, THE LEADING EDGE FLAPS AND SLATS AND THE DRIVE MECHANISMS BEFORE YOU MOVE THE FLAP CONTROL LEVER. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (c)  Move the flap control lever to extend and retract the flaps. Carefully monitor the operation of the bellcrank.
 NOTE: Make sure the bellcrank does not touch the cam track
____ during flap operation. If the bellcrank touches the cam track, then adjust the shims at the cam track attach points.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-52
 ALL  ú ú 03 Page 408 ú Jul 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 834-033
 (4)  
Do this task: "Outboard Flap Track Fairing Adjustment"
 (Ref/27-51-52/501).

 E.
Put the Airplane Back to Its Usual Condition

 S 444-022
 (1)  Do this task: "Trailing Edge Flap System Activation"
 (Ref 27-51-00/201).

 S 864-023
 WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF ALL CONTROL
_______ SURFACES BEFORE YOU SUPPLY HYDRAULIC POWER. AILERONS, RUDDERS, ELEVATORS, FLAPS, SPOILERS, LANDING GEAR, AND THRUST REVERSERS CAN MOVE QUICKLY WHEN YOU SUPPLY HYDRAULIC POWER. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
　
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 飞行操纵 FLIGHT CONTROLS 4(85)