737-300 400 500 AMM 飞机维护手册 ENGINE 发动机 2(5)

曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

There is no limit on the quantity of nicks and dents on the trailing edge if not more than 0.015 inch (0.3 mm) in depth.There is no limit on the quantity of nicks, dents and scratches on the contour surface as follows: a) The damage is not more than 0.005 inch (0.1 mm) in
 depth. b) The scratches are not more than 0.4 inch (10.0 mm) in
 length.Nicks, dents and scratches on the mid-span shroud to airfoil fillet are not serviceable.Mid-span shroud (does not include fillet): a) There is no limit on the quantity of pits if not more
 than 0.005 inch (0.1 mm) in depth. b) There is no limit on the quantity of nicks, dents and scratches as follows:
 1.  The nicks and dents are not more than 0.01 inch
_
 (0.2 mm) in depth.
 2.  A 50 cycle maximum service extension is permitted
_
 if the nicks, dents and sheared edges are not more
 than 0.035 inch (0.9 mm) in depth.

 c)  There is no limit on the quantity of wear because of shingling if not more than 0.005 inch (0.1 mm) in depth after the removal of high metal.
 d)  No more than 10% of the hardcoat can be flaked off.
 1.  
A 250 cycle maximum service extension is permitted

_
 if no more than 25% of the coating is missing.

 2.  
A 50 cycle maximum service extension is permitted

_ if no more than 40% of the coating is missing. e) Flaking of the aluminum coating
 1.  
Use the tool, 856A3629 to make sure the aluminum

_
 coating at the end of the convex side of the
 37-degree mid-span shroud is in the limits
 (Fig. 604).

 2.  
If the damage is more than the limits, replace the

_
 fan blade (AMM 72-31-02/401).Cracks or tears on the Area C are not serviceable.If there is distortion in Area C, the limits are as follows:
 NOTE: To find if a fan blade has distortion, compare it to
____ the other blades from the rotor.
 The trailing edge contour in this area can change because of the forging process. This is permitted. Examine for distortion because of FOD or birdstrikes.
 a)  No more than 0.34 inch (8.0 mm) out of contour in two locations.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 72-31-02
 ALL  ú ú C02 Page 616 ú Jul 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////

S-M56-MM-03146-00-B
37 Degrees Convex Mid-Span Shroud Inspection Details Figure 604
F10161
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 72-31-02
 ALL  ú ú C02 Page 617 ú Jul 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
b)  The length (D) must be more than six times the depth
 (C) (Fig. 601)
 c)  Do a flourescent penetrant inspection of the area (AMM 70-40-01/201)
 (h)  Area D: 1) There is no limit on the quantity of nicks and dents on the leading edge if not more than 0.04 inch (1.0 mm) in depth. 2) There is no limit on the quantity of nicks and dents on the trailing edge if not more than 0.04 inch (1.0 mm) in depth.
 3)  There is no limit on the quantity of nicks, dents and scratches on the contour surface as follows: a) The damage is not more than 0.015 inch (0.3 mm) in
 depth. b) The scratches are no more than 0.4 inch (10.0 mm) in length. 4) Tip: a) There is no limit on the quantity of nicks and dents as follows:
 1.  
The scratches are no more than 0.25 inch (6.3 mm)

_
 in length.

 2.  
The damage is no more than 0.04 inch (1.0 mm) in

_ depth. b) There is no limit on the quantity of blades with tip curl of the leading edge as follows:
 1.  The tip curl does not extend more than 0.5 inch
_
 (12.7 mm) across the blade tip.
 2.  The tip curl does not extend more than 0.5 inch
_
 (12.7 mm) down the leading edge.
 3.  
　
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 ENGINE 发动机 2(5)