(d)
Remove and discard the O-ring from the TGB adapter sleeve.
(e)
Remove and discard the O-ring from the sleeve of the horizontal drive shaft.
S 214-027-C00
(20)
Do a check of the oil retaining sleeve of the horizontal drive shaft (AMM 72-62-03/201).
(21)
Put end caps on all open tubes and oil ports on the TGB.
S 034-029-C00
(22)
Install end caps on the end of the horizontal drive shaft and the TGB adapter sleeve.
S 034-028-C00
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
72-62-01
ALL ú ú C05.1 Page 417 ú Jul 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
S 034-030-C00
(23) Install an end cap in the opening of the AGB and the fan frame.
TASK 72-62-01-404-004-C00
3. Transfer Gearbox Installation
_____________________________
A. Equipment
(1)
Adapter, AGB Locking - 856A3509, CFM International, P.O. Box 15514, Cincinnati, OH 45215
(2)
Part Power Rig Pin - C76001
(stored in fly-away kit located in electronics
compartment [kit is secured to forward outboard
leg of battery support]) or equivalent 0.248
(+0.000/-0.003) inch [6.30 (+0.00/-0.08) mm]
diameter, 2.5 inch (64 mm) minimum length rod
or bolt with warning streamer attached.
(3)
Wrench - 856A3604, CFM International
B. Consumable Materials
(1)
Grease - CP2101 (Ref 70-10-01)
(2)
Oil - Engine (Ref 70-10-01)
C. References
(1)
AMM 70-30-01/201, Seals (Preformed Packings and O-rings) and Gaskets
(2)
AMM 71-00-00/501, Power Plant Reference Table
(3)
AMM 71-11-02/201, Fan Cowl Panels
(4)
AMM 76-11-00/501, Engine Controls
(5)
AMM 78-31-00/201, Thrust Reverser
D. Access
(1)
Location Zones
506 Engine No. 1 - Fan Frame
606 Engine No. 2 - Fan Frame
(2)
Access Panels
5738L/5838R Engine No. 1 - Thrust Reverser
5739L/5839R Engine No. 2 - Thrust Reverser
5746L/5846R Engine No. 1 - Fan Cowl
5737L/5837R Engine No. 2 - Fan Cowl
E. Install the Transfer Gearbox (TGB).
NOTE: Unless specified differently, when this procedure refers to
____
lubricated bolts, use the bolts which have the threads
lubricated with engine oil.
NOTE: When you install the packing, make sure you lubricate the
____
packings with engine oil.
S 424-031-C00
(1) Do these steps to install the TGB (Fig. 403):
(a) Remove the end caps from the adapter sleeve and the end of the horizontal drive shaft.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
72-62-01
ú ALL ú
ú ú ú C06.101 ú BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details. Page 418Jul 12/02
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
(b)
Remove the end cap from the AGB and the fan frame.
(c)
Install a new lubricated O-ring on the adapter sleeve.
(d)
Make sure the adapter sleeve and the horizontal drive shaft are fully retracted.
CAUTION: BE CAREFUL WHEN YOU ENGAGE THE RADIAL DRIVE SHAFT WITH THE
_______
INPUT BEVEL GEAR OF THE TGB. IF YOU ARE NOT CAREFUL,
DAMAGE TO THE SEALS AND THE SPLINES COULD OCCUR.
(e)
Lift the TGB and move the TGB until its splines correctly
engage the splines of the input bevel gear on the TGB.
(f)
Do these steps to attach the TGB to the fan frame:
1) Apply a thin layer of grease to the threads of the
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 ENGINE 发动机 2(127)
