曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
G. System A and system B pressure is supplied by engine-driven hydraulic pumps on each engine and electric motor driven hydraulic pumps (one for each system). A and B flight control hydraulic modular units are identical in components and operation. Pressurized hydraulic fluid flows through the modular unit which consists of a spoiler shutoff valve, a flight controls shutoff valve, low pressure warning switch, compensator, and check valve. The flight controls shutoff valve controls the flow of hydraulic fluid to the ailerons, elevator, and rudder. When either the A or B flight control switch on the overhead panel is moved to STBY RUD, or if the automatic standby function is activated, the standby hydraulic system pump will start. The standby rudder actuator shutoff valve located in the standby hydraulic module will also open, porting hydraulic fluid to the standby actuator.
H. A rudder isolation shutoff valve is installed in the system A and the system B hydraulic lines between the respective system A and system B flight controls hydraulic modular units and the rudder power unit. The valve is part of the hydraulic isolation shutoff valve module, which consists of six hydraulic isolation valves. The valves are individually operated and provide a means of isolating individual hydraulic components for ground leakage and flow tests.
2. Rudder
______
A. The rudder provides yaw control for the airplane. The rudder is of graphite/composite construction. The skin is made of graphite reinforced epoxy. There is no rudder tab. There are seven rudder hinges, the bottom one being a thrust hinge. Balance weights are fastened to the rudder nose. The balance weights are made of tungsten. See Structural Repair Manual, Chapter 51, for rudder balancing. There is a body seal attached to the bottom rib of the rudder. The body seal is made of honeycomb nomex core material. This seals the gap between the rudder and the body.
3. Rudder Pedals
_____________
A. The captain and first officer are each provided with a pair of rudder pedals used for controlling the airplane about the vertical axis (Fig. 1). Each pair of pedals consist of right and left pedals mounted on a shaft. The pedal shaft is attached to the upper end of the pedal arm assembly. The lower end of the pedal arm assembly is mounted on a support shaft attached to the structure below the floor. The rudder pedals are located below the captain's and first officer's instrument panel. Rudder pedal support and quadrant assemblies are accessible through the lower nose compartment.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-21-00
ALL ú ú 02 Page 4 ú Mar 15/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
Rudder Aft Control Quadrant and Torque Tube
Figure 2
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-21-00
ALL ú ú 01 Page 5 ú Jun 25/84
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
4.
5.
6.
A
737-300/400/500MAINTENANCE MANUAL
B. Fore and aft movement of the pedals is transmitted by the two pushrods to the jackshaft yoke. The rotary motion of the jackshaft yoke is passed to the forward quadrant by means of the jackshaft. The two sets of rudder pedals are bussed together by means of a bus pushrod connecting the two jackshaft assemblies. Toe pressure on the rudder pedals causes pedals to rotate about the shafts and initiate braking action.
Rudder Pedal Adjustment Crank
_____________________________
A. The two pairs of rudder pedals can be adjusted independently to suit the captain and first officer. This is accomplished by means of the rudder pedal adjust shaft (Fig. 1). The rudder pedal adjustment mechanism consists of an adjustment crank, adjustment shaft, a jackscrew, and pedal adjustment nut attached to the jackshaft assembly.
B. The adjustment crank is located on the instrument panel forward of the control wheel. The crank is connected to a flexshaft routed forward under the instrument panel, then down under the floor, and aft to the universal joint in the rudder control jackshaft assembly. Rotation of the rudder pedal adjustment crank actuates the jackscrew which causes the yoke, containing the pedal adjustment nut, to move fore and aft.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 飞行操纵 FLIGHT CONTROLS 2(6)
