NO
PROCEDURES ARE PROVIDED FOR BOTH ALUMINUM AND
27-31-00-735-037?
TITANIUM PUSHRODS
FREEPLAY REQUIREMENTS MUST BE MET TO OBTAIN CORRECT TAB POSITION
TOOL C27028, OR EQUIVALENT, IS RECOMMENDED YES FOR NECESSARY ACCURACY
MEASURE USING FOUR POINT METHOD (PREFERRED), OR BY SINGLE POINT METHOD
Elevator Tab Adjustment Flow Diagram
Figure 507A
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-31-00
ALL ú
ú 02 Page 523
ú Jul 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
F92107
A
737-300/400/500MAINTENANCE MANUAL
ACCESS PANEL
ELEVATOR TAB
LOWER INBOARD
HINGE COVER
INBD
HORIZONTAL
STABILIZER TAB PUSHRODS
SEE A FWD
ELEVATOR
ELEVATOR
LOWER TAB ELEVATOR TAB CHECKNUTS (EXAMPLE) 1 TAB PUSHRODS
AERODYNAMIC
SEAL
AFT MOUNTING BOLT (EXAMPLE)
INBD
A
1 ON AIRPLANES WITH TITANIUM TAB RODS, DO NOT INSTALL LOCKWIRES
Elevator Tab Pushrod Adjustment Figure 508
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-31-00
ALL ú ú 02 Page 524 ú Jul 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
(a)
(b)
(c)
(d)
(e)
(f)
(g)
(h)
A
737-300/400/500MAINTENANCE MANUAL
Do this task: "Remove the Pressure from the Elevator Hydraulic
Systems A and B" (AMM 27-31-00/201).
Make sure that the B dimension is at 41.57 |0.01 inches.
Remove the access panel 9313L or 9413R (access panels of the
tab pushrod at the upper inboard end of the elevator).
Determine if titanium or aluminum tab pushrods are installed.
NOTE: The aft ends of the titanium pushrods have two
____ checknuts for each pushrod. The aft ends of the aluminum pushrods have one checknut for each pushrod.
If aluminum tab pushrods are installed, remove the access panels 9105 or 9205.If aluminum tab pushrods are installed, loosen the checknuts at each aft and forward end of the two right hand elevator tab pushrods.If titanium tab pushrods are installed, loosen the two checknuts on each of the two right hand elevator tab pushrods.Use the C27032 ski jump tool and do the steps that follow to measure the stabilizer to elevator gap (ski jump) for the right elevator (Fig. 508A).
NOTE: The ski jump measurement is an optional measurement.
____
1) Use the zero block to adjust the dial indicator of the ski
jump tool assembly to zero. 2) Push the elevator trailing edge full up. 3) While you move the elevator trailing edge down, align the
center of the right elevator trailing edge with the index mark within |0.04 inch or less.
NOTE: Keep the elevators at this position while you do
____ the steps to find the ski jump value for the right elevator. If the elevator position is changed, you must put the elevator trailing edge at the full up position and do this step again before you continue.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-31-00
ALL ú ú 02 Page 525 ú Jul 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
APPROXIMATE MEASUREMENT POSITIONS (INCHES)
Ski Jump Tool and Measurement
Figure 508A
E37841
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-31-00
ALL ú ú 02 Page 526 ú Jul 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
4)
A
737-300/400/500MAINTENANCE MANUAL
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址:737-300 400 500 AMM 飞机维护手册 飞行操纵 FLIGHT CONTROLS 2(110)