micrometer reading.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-31-00
ALL ú ú 02 Page 535 ú Jul 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
ELEVATOR
DIMEMSION TAB HORIZONTAL "X"STABILIZER
SET THE TOOL AT SECOND TAB HINGE
(FROM INBOARD)
ELEVATOR TAB
RIGGING FIXTURE
FWD
ELEVATOR "X" DIMENSION
FEEL COMPUTER
STABILIZER
INPUT ROD
SEE A
CHECKNUT
STABILIZER INPUT ROD FWD
INPUT ARMINPUT ARM RIG PIN
A
FWD
RIGGING FIXTURE C27028 MEASURES "X"
DIRECTLY FROM THE LOWER SURFACE OF
THE ELEVATOR.
RIGGING FIXTURE F80248-() OR TE27T-31001-()
TAKES "X" DIMENSION FROM BOTTOM OF TAB TO
TOP OF TOOL
Feel Computer Input Rod Adjustment
Figure 509
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-31-00
ALL ú ú 02 Page 536 ú Jul 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
c) Move the digital micrometer up until it gives the same reading as the calibration value stamped on the side of the tool.
NOTE: This brings the pointer on the micrometer up to____ approximately 0.3 inch below the trailing edge of the elevator tab.
2) 3) d) Push the button on the micrometer to zero the micrometer reading. e) Push the elevator trailing edge full up. f) While you move the elevator trailing edge down, align the center of the right elevator trailing edge with the index mark within |0.04 inch or less.If you use the F80248-8 (alternative) rigging fixture or the TE27T-31001-( ) (alternative) rigging fixture, do the steps that follow:Set the tab rigging fixture below and along the elevator rib at the second inboard tab hinge.
NOTE: The fixture must only touch the elevator at the____ spacers. The permitted difference in thickness of the spacers is 0.005 inch.
4) Measure the X dimension which is measured perpendicular to the elevator lower surface at the tab trailing edge.
NOTE: This will be ADJ.____
5) 6) Calculate the initial tab dimension Xi from Table 504.The tab position at the second hinge, ADJ, will be adjusted to agree with the value of Xi.
EXAMPLE: Xi from Table 503 (or Table 504) is 0.320 inch_______ and the measured tab position is 0.360 inch. Therefore the tab trailing edge must be lowered by 0.04 inch.
7) While you move the elevator trailing edge down, align the center of the left elevator trailing edge with the index mark within |0.04 inch or less.
NOTE: Keep the elevators at this position while you do____ the steps to measure the elevator tab position. If the elevator position is changed, you must put the elevator trailing edge at the full up position and do this step again before you continue.
8) Do these steps again to measure the left elevator tab position.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-31-00
ALL ú ú 05 Page 537 ú Jul 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
(m) Adjust the right tab pushrods if the difference between Xi (Table 503 or Table 504) and the measured average tab position (ADJ) is more than |0.01 inch. 1) Coarse adjustment:
NOTE: Do the coarse adjustment only if the difference
____ between Xi (Table 503 or Table 504) and the measured tab position (ADJ) (for the four point of the single point method) is more than |0.1 inch or you cannot get the necessary tab setting with the fine adjustment.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 飞行操纵 FLIGHT CONTROLS 2(115)
