position.
(d)
Install the rig pin R4 in the feel, centering and trim mechanism.
S 735-082
(2)
Bearing play test for the lower rudder.
(a)
Install the rudder flutter test fixture to the upper rudder trailing edge.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-21-00
ALL ú ú 01 Page 535 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
INDICATOR
Rudder Flutter Test Fixture Installation
Figure 506
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-21-00
ALL ú ú 01 Page 536 ú Jun 10/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
E99170
A
747-400 MAINTENANCE MANUAL
(b) Adjust the dial indicator to touch the trailing edge of the lower rudder.
CAUTION: DO NOT PUT A PRESSURE OF MORE THAN 5 PSI ON THE RUDDER
_______ SURFACE. USE PIECES OF WOOD TO APPLY THE FORCE OVER A LARGER AREA. A LARGE FORCE ON A SMALL AREA OF THE RUDDER WILL CAUSE DAMAGE TO IT.
(c) Push with 8-12 pounds on the left side of the lower rudder, aproximately 11 inches in from the trailing edge, and hold.
NOTE: You must apply the force over a minimum area of three
____
square inches.
1) Set the dial indicator to zero.
(d) Push with 8-12 pounds on the right side of the lower rudder, aproximately 11 inches in from the trailing edge, and hold.
NOTE: You must apply the force over a minimum area of three
____
square inches.
1) If the dial indicator shows more than 0.21 inch, the rudder hinge bearings or the bearings for the power control package have too much play.
NOTE: Correct all the problems before you continue with
____
the test.
(e) Remove the rudder flutter test fixture.
S 735-083
(3)
Bearing play test for the upper rudder.
(a)
Install the rudder flutter test fixture to the vertical fin of the trailing edge (Fig. 506).
(b)
Do the steps for the bearing play test for the lower rudder, but push on the upper rudder.
NOTE: The upper rudder has the same play allowance of 0.21
____
inch as the lower rudder.
(c)
Remove the rudder flutter test fixture.
(d)
Remove the rig pin R4.
L.
Rudder Trim Switch Test
S 845-100
(1)
Prepare for the test.
(a)
Shake the rudder pedals to make sure they are in their center position.
(b)
Make sure the rudder trim indicator on the control stand is at zero.
(c)
Make sure the rudder is at 0.0 +/- 1.0 degrees.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-21-00
ALL ú ú 01 Page 537 ú Jun 10/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
S 215-163
(2)
During the test for the rudder trim switch, make sure the rudder trim knob does not touch the lightplate surface.
S 735-085
(3)
Procedure
(a)
Turn the rudder trim switch fully counterclockwise (nose left). 1) Make sure the rudder moves.
(b)
Release the rudder trim switch. 1) Make sure the rudder trim switch goes to its center
position immediately.
2) Make sure the rudder stops.
(c)
Turn the rudder trim switch fully clockwise (nose right). 1) Make sure the rudder moves.
(d)
Release the rudder trim switch. 1) Make sure the rudder trim switch goes to its center
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：747-400 AMM 飞机维护手册 飞行操纵 FLIGHT CONTROLS 2(61)
