S 494-019
(3)
Disconnect the hydraulic lines H1 and H2 from the actuator (4):
(a)
Put a bucket below the actuator to catch the hydraulic fluid.
(b)
Disconnect the hydraulic lines from the actuator.
(c)
Install caps on the hydraulic lines.
S 024-022
(4)
Remove the upper actuator (4):
(a)
Remove the nut (16) and washer (15).
(b)
Remove the bolt assembly (11).
(c)
Use the fishpole hoist and the hoist frame equipment to hold the actuator (4).
(d)
Remove the four bolts (9) and washers (10) that connect the actuator (4) to the pillow block (3).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-21-16
ALL ú ú 01 Page 407 ú Feb 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
(e) Retract the piston in the actuator (4).
NOTE: Use the bucket to catch the hydraulic fluid.
____
(f)
Install the caps on the hydraulic ports.
(g)
Remove the actuator (4) through the opening in the right side of the vertical stabilizer.
S 494-071
(5)
If you will not install the upper actuator immediately, do these steps to install the rudder actuator lock (referred to as the lock):
(a)
Put the lock in the location of the actuator that you removed.
(b)
Attach the lock to the pillow block (3) with its four bolts.
(c)
Adjust the length of the lock until you can connect it to the rudder with the pin.
(d)
Install the three lockpins in the lock.
(e)
Remove the rudder clamp from between the upper and lower rudders.
TASK 27-21-16-404-024
4. Lower Rudder Upper Actuator Installation (Fig. 401)________________________________________
A. Special Tools and Equipment
(1)
ST2580-267, Spanner Wrench Set
(2)
3ME65B81000-1, Rudder Clamp
(3)
G27008-19, Rudder Actuator Lock
(4)
G27016-39, Hoist Frame Equipment - Upper and Lower Rudder P.C.U.
(5)
Fishpole Hoist - P/N PF51-009-1 or Equivalent
PF Industries
Hoist Minilift
Didsbury Engineering
B.
Consumable Materials
(1)
A00181, Adhesive - BMS 5-92
(2)
A00247, Sealant - BMS 5-95
(3)
D00054, Lubricant - Skydrol Assembly Lube MCS352
(4)
D00153, Fluid, Hydraulic Fire Resistant - BMS 3-11
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-21-16
ALL ú ú 01 Page 408 ú Feb 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
C. Parts ~.............................................................................. | AMM | | AIPC | ................. ...........................| | FIG | ITEM | NOMENCLATURE | SUBJECT | FIG | ITEM | ...............................................................................| | 401 | 4 | Actuator Upper | 27-21-16 | 02 | 295 | | | 9 | Bolt | | | 260 | | | 10 | Washer | | | 265 | | | 11 | Bolt Assy | | | 245 | | | 14 | Bushing | | | 240 | | | 15 | Washer | | | 250 | | | 16 | Nut | | | 255 | | | 35 | Wire Bundle Clamp | | | | | | | | | | | 2......…........…...................................…...........….....…........1
D. References
(1)
AMM 27-21-16/501, Lower Rudder Power Control Actuator
E.
Access
(1)
Location Zone
324 Vertical Fin, Rear Spar to Trailing Edge
325 Lower Rudder
F.
Procedure
S 494-025
(1)
Do these steps to install the rudder clamp, and remove the rudder actuator lock (referred to as the lock):
(a)
Make sure the upper rudder is aligned with the lower rudder.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：747-400 AMM 飞机维护手册 飞行操纵 FLIGHT CONTROLS 2(142)
