B.
References
(1)
06-09-07/201, Fin and Rudder Access Doors and Panels
(2)
09-11-00/201, Towing
(3)
24-22-00/201, Manual Control
(4)
27-21-00/501, Rudder Ratio Changer Existing Faults Check
(5)
27-21-00/524, Procedure 1
(6)
27-51-00/201, Trailing Edge Flap System
(7)
29-11-00/201, Main Hydraulic Supply System
(8)
31-61-00/201, Integrated Display System
(9)
34-11-00/201, Pitot-Static System
(10)
AMM 45-10-00/201, Central Maintenance Computer
C.
Access
(1)
Location Zone 324 Vertical Fin, Rear Spar to Trailing Edge 221-222 Control Cabin
D.
Prepare for the Test
(1)
Install rig pin E-2 at the bottom of the elevator aft quadrant.
S 495-040
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-21-12
ALL ú ú 01 Page 512 ú Oct 10/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 495-041
WARNING:_______MAKE SURE THE NOSE LANDING GEAR IS POINTED FORWARD. IF THE TIRES ARE NOT PARALLEL WITH THE AIRPLANE , THEY CAN TURN QUICKLY WHEN YOU REMOVE THE TOW PIN. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(2) Install the TOW PIN at the steering metering valve for the nose landing gear (Ref 09-11-00/201).
NOTE: This is to make sure the nose landing gear does not turn.
____
S 865-042
(3)
Supply electrical power (Ref 24-22-00/201).
S 865-067
(4)
Make sure that the EICAS is serviceable (Ref 31-61-00/201).
S 865-044
(5)
Make sure that the CMC is serviceable (AMM 45-10-00/201).
E.
Rudder Ratio Changer Error Message Test
S 745-045
(1)
Look for these messages on EICAS and the CDU.
(a)
Make sure the RUD RATIO SNGL and RUD RATIO DUAL amber messages do not show on the upper EICAS.
(b)
Do the rudder ratio changer existing faults check (Ref/27-21-00/501).
(c)
Open this circuit breaker:
1) P7, Overhead Circuit Breaker Panel a) 7B12 UPR RUD RATIO AC PWR
(d)
Stop for a minimum of 5 seconds.
(e)
Make sure the RUD RATIO SNGL amber message shows on the upper EICAS.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-21-12
ALL ú ú 01 Page 513 ú Oct 10/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
(f)
Open this circuit breaker:
1) P7, Overhead Circuit Breaker Panel a) 7B14 LWR RUD RATIO AC PWR
(g)
Stop for a minimum of 5 seconds.
(h)
Make sure the RUD RATIO DUAL amber message shows on the upper EICAS. 1) Close these circuit breakers:
a) 7B14 LWR RUD RATIO AC PWR b) 7B12 UPR RUD RATIO AC PWR
F. Rudder Ratio Changer Test for Correct Rudder Travel
S 865-052
WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF ALL CONTROL
_______ SURFACES BEFORE YOU SUPPLY HYDRAULIC POWER. THE AILERONS, RUDDERS, ELEVATORS, FLAPS, SPOILERS, LANDING GEAR, AND THRUST REVERSERS CAN MOVE QUICKLY WHEN YOU SUPPLY HYDRAULIC POWER. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(1)
Pressurize the four hydraulic systems (Ref 29-11-00/201).
S 865-048
(2)
Set the rudder trim to zero.
S 715-053
CAUTION:_______MOVE THE RUDDER PEDALS SMOOTHLY AND SLOWLY. THE MINIMUM TIME TO MOVE THE RUDDER PEDAL FROM ITS CENTER POSITION TO ITS FULL TRAVEL POSITION IS 2 SECONDS. IF YOU MOVE THE RUDDER PEDALS TOO FAST YOU CAN CAUSE DAMAGE TO THE POWER CONTROL PACKAGE.
(3)
Low speed test (0 knots)
(a)
Push the captain's left rudder pedal fully forward and hold it.
1) Make sure the rudder position indicators on the status page of EICAS show the rudders are fully left (the pointers are left of the third ten degree mark).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：747-400 AMM 飞机维护手册 飞行操纵 FLIGHT CONTROLS 2(125)
