737-300 400 500 AMM 飞机维护手册 发动机燃油和控制(81)

曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
c)  The test will continue until a failure occurs or you push the STOP switch.
 d)  If a failure occurred during the test, the red FAIL light will come on, and the message, FAIL, along with the test value will be shown on the display.
 e) To do the test again, push the STRT switch. f) To do a different test, push the STOP switch and put the new test number in the tester.
 (h) Do the NLR Schedule Test (Test 1) in the MANUAL mode.
 NOTE:____This test has 12 separate functional checks. Four checks are done at the ambient pressure, and eight checks are done at alternate pressures. These checks permit you to do a test of the system at different PLA, T12 and PS12 values, and to make sure that the NLR (fan speed) set by the PMC is in the specified limits.
 1)  Put the number 1 (for Test No. 1) in the tester and push the STRT key. a) After the test is completed at the ambient pressure,
 the message SET PRESS TO 4 PSIA will show on the display. 2) Connect the pressure controller to the PS12 sensor on the PMC (Fig. 504).
 CAUTION:_______DO NOT PUT TOO MUCH PRESSURE IN THE PS12 PORT. TOO MUCH PRESSURE CAN CAUSE DAMAGE TO THE PS12 SENSOR IN THE PMC.
 3)  Do these steps to apply the 4 psia pressure source: a) Put the switch on the pressure controller cylinder to
 the OPEN position. b) Turn the wheel fully in the clockwise (CW) direction. c) Put the switch in the CLOSED position. d) Turn the wheel in a counterclockwise (CCW) direction
 until a pressure of 4 PSIA is shown on the pressure
 gage.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 73-21-00
 ALL  ú ú C02 Page 524 ú Jul 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
4) The test No. 1 will continue when the 4 |0.10 psia pressure source is applied to the tester. 5) Continue the test with pressures of 6, 12 and 14 psia as necessary.
 (i)  Do the PMC Activate Switch Test (Test No. 21) in the MANUAL mode. 1) Use the data given from the tester to replace the PMC
 and/or related components as necessary (Fig. 505).
 S 085-044-C00
 (3)  
Remove the power to the PMC tester unit and disconnect the unit and
 the power supply for the PMC tester

 S 435-045-C00

 (4)  
Install the electrical connectors and the protective caps again.

 S 415-046-C00

 (5)  
Close the fan cowl panels (AMM 71-11-02/201).

 I. PMC and Related Components Tests (PMC Resistance Tester)
 NOTE: This procedure permits you to do troubleshooting of the PMC and
____
 the related components. To do this procedure, the inputs to the
 PMC are isolated.

 You cannot do all the checks that you can with the PMC tester. As an example, you cannot do a check of the PS12 transducer or the NLR schedule.
 If you follow this procedure to find out if the PMC should be replaced, make sure you check the related components. Make sure that all of the related components operate correctly.
 S 765-076-C00
 (1)  Test Setup Procedure
 (a)  Set the PMC System Resistance Tester switches 1, 2, 3, and 4 in position 0.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 73-21-00
 ALL  ú ú C02 Page 525 ú Jul 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL  //////////////////////// //////////////////////// / / / /CFM56 ENGINES 
Test 
Number______  Description___________  If Test Fails_____________ 
1  NLR Schedule  Replace PMC (73-21-04)
 2 Torque Motor (T/M) Current Limiter  Replace PMC (73-21-04) 
3 T12 Open Circuit  Replace PMC (73-21-04)
 4  Overspeed Fail-Safe  Replace PMC (73-21-04) 
5 Not Applicable 
6 Not Applicable 
7 Not Used 
　
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 发动机燃油和控制(81)