73-21-01
ALL ú ú C02 Page 408 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
SEE A
SEE C
SEE B
INNER MEMBER
VSV FEEDBACK CABLE NOSE CAP FOR THE
SEE D
VSV FEEDBACK CABLE CONDUIT CAP FOR THE A
VSV and VBV Feedback Cable Installation Figure 403 (Sheet 1)
NOSE CAP FOR THE VBV FEEDBACK CABLE
CONDUIT CAP FOR THE VBV FEEDBACK CABLE
VBV MEC BRACKET
VSV MEC BRACKET
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
73-21-01
ALL ú ú C02 Page 409 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
ROD END BEARING OF THE VSV FEEDBACK CABLE
MEC
FEEDBACK ARM
PIN
FILLISTER HEAD SCREW
HEX SLOTTED
HEX
VSV and VBV Feedback Cable Installation
Figure 403 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
73-21-01
ALL ú ú C01 Page 410 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
(b)
Discard the cotter pin from the rod end bearing.
(c)
Remove the nut, the bolt and the washer.
CAUTION: YOU MUST RETRACT THE CABLE INNER MEMBER BEFORE YOU REMOVE
_______ THE SUPPORT TUBE ASSEMBLY. THIS WILL PREVENT DAMAGE TO THE EXPOSED INNER MEMBER.
(d) Move the cable inner member to the fully retracted position at the MEC end.
CAUTION:_______DO NOT TWIST THE FEEDBACK CABLE. USE TWO WRENCHES WHEN YOU LOOSEN THE NOSE CAP, ONE ON THE NOSE CAP AND ONE ON
THE CONDUIT CAP. THIS WILL PREVENT DAMAGE TO THE
HARDWARE.
(e) Loosen the nose cap.
NOTE:____ Do not disconnect the nose cap and the conduit cap.
(f) Carefully move the conduit cap away from the MEC slotted
bracket.
S 684-020-C00
CAUTION: USE TWO WRENCHES WHEN YOU REMOVE THE COUPLING NUTS FOR THE FUEL
_______ SUPPLY LINE, ONE TO HOLD THE FITTING AND ONE TO LOOSEN THE COUPLING NUT. THIS WILL PREVENT DAMAGE TO THE HARDWARE.
(10) Drain the fuel from the fuel lines, the fuel pump and the MEC as follows (Fig. 404):
(a) Put a container below the MEC to catch the fuel.
NOTE: The quantity of fuel that will drain is approximately
____ 1.0 gallons.
(b)
Remove the drain plug for the fuel filter. 1) Let the fuel drain into the container.
(c)
Remove and discard the O-ring from the drain plug.
(d)
Loosen the fuel inlet line at the strut disconnect panel sufficiently to let the air enter the fuel inlet line.
NOTE: Put a funnel or a container below the inlet line
____ connection of the fuel supply. Do not let the fuel spill on the fan case.
(e)
Lubricate a new O-ring with the petrolatum.
(f)
Install the new O-ring on the drain plug.
(g)
Apply a thin layer of graphite grease on the threads of the drain plug.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
73-21-01
ALL ú ú C02 Page 411 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
(h) Install the drain plug.
1) Tighten the drain plug to 45-55 pound-inches
(5.1-6.2 Newton meters).
2) Install the lockwire.
S 034-021-C00 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：737-300 400 500 AMM 飞机维护手册 发动机燃油和控制(100)
