5) Turn the transmitter to get a display of 0000. 6) Tighten the clamp screws to 30-35 pound-inches.
WARNING: MAKE SURE PERSONS AND EQUIPMENT ARE CLEAR OF ALL
_______ CONTROL SURFACES BEFORE YOU SUPPLY HYDRAULIC POWER. AILERONS, RUDDERS, ELEVATORS, FLAPS, SPOILERS, LANDING GEAR, AND THRUST REVERSERS CAN MOVE QUICKLY WHEN YOU SUPPLY HYDRAULIC POWER. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
7) Supply power to the hydraulic system A and B (Ref 29-15-00/201).
(d)
Put the elevator in the position shown in the table.
(e)
At each position, make sure the portable tester display agrees with the value in the table.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. BEJ 101-999 ú
31-24-51
ú ú 12 Page 503 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
~............................................................ | ELEVATOR POSITION | PORTABLE TESTER | | | DISPLAY | .............................................................. | at index mark | 7733 to 0044 | .............................................................. | 10.00 inch above index | 7224 to 7332 | .............................................................. | 10.00 inch below index | 0502 to 0626 | 2..............................….............................1
S 865-075
(5) Do these steps for the right elevator position transmitter:
(a)
BEJ 113;
Set the portable tester to subframe 1, word 45.
(b)
BEJ 101-112; Set the portable tester to subframe 0, word 37. 1) Make sure the portable tester display shows 0000.
(c)
If the display does not show 0000, do these steps: 1) Remove hydraulic systems A and B (AMM 27-21-00/201). 2) Open access panel to get access to the right elevator
transmitter. 3) Turn the transmitter until the mark align with the mark on the transmitter.
NOTE: No special position of the aligned marks is
____
necessary.
4) Turn the transmitter to get the display of 0000.
5) Tighten the clamp screws to 30-35 pound-inches.
WARNING: MAKE SURE PERSONS AND EQUIPMENT ARE CLEAR OF ALL
_______ CONTROL SURFACES BEFORE YOU SUPPLY HYDRAULIC POWER. AILERONS, RUDDERS, ELEVATORS, FLAPS, SPOILERS, LANDING GEAR, AND THRUST REVERSERS CAN MOVE QUICKLY WHEN YOU SUPPLY HYDRAULIC POWER. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
6) Supply power to hydraulic systems A and B (Ref 29-15-00/201).
(d)
Put the elevator in the positions shown in the table.
(e)
At each position, make sure the portable tester display agrees with the values in the table.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. BEJ 101-999 ú
31-24-51
ú ú 12 Page 504 ú Mar 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
~............................................................ | ELEVATOR POSITION | PORTABLE TESTER | | | DISPLAY | .............................................................. | at index mark | 7734 to 0045 | .............................................................. | 10.00" above index | 0446 to 0554 | .............................................................. | 10.00" below index | 7152 to 7276 | 2..............................….............................1
F. Put the Airplane to its Usual Condition
S 865-063
(1)
Set the TEST--NORMAL switch to the NORMAL position.
S 865-064
(2)
Put the POWER switch on the portable tester to the OFF position.
S 085-065
(3)
Disconnect the portable tester from the flight data recorder system.
S 415-067
(4)
Close the forward access door 1103.
(5)
Remove the hydraulic power (Ref 27-21-00/201).
S 865-069
(6)
Remove the electrical power if it is not necessary
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 仪表 INSTRUMENTS(110)
