(c)
Install the O-rings and the unions in the hydraulic ports.
S 424-012
(3)
Install the actuator for the flight spoiler:
(a)
Remove the caps from the hydraulic lines.
(b)
Put the actuator in its position on the structure with the hydraulic ports aligned with the hydraulic lines.
(c)
Loosely connect the hydraulic lines to the actuator.
(d)
Install the four bolts to attach the actuator to the structure:
CAUTION: MAKE SURE YOU DO NOT INSTALL A WASHER ON THE SHORT
_______ TOP BOLT. THE BOLT CAN TOUCH THE ACTUATOR DURING THE OPERATION OF THE ACTUATOR. YOU CAN CAUSE DAMAGE TO THE ACTUATOR.
1) Install the short top bolt without a washer to attach the actuator. 2) Install the three remaining bolts with washers to attach
the actuator.
3) Tighten the two top bolts to 450-550 pound-inches.
4) Tighten the two bottom bolts to 225-275 pound-inches.
(e) Tighten the hydraulic lines on the actuator.
S 434-013
(4)
Connect the actuator link to the input arm:
(a)
Install the bolt in the forward position of the input arm with the bolt head left.
(b)
Install the washer and nut on the bolt.
(c)
Install the cotter pin.
(d)
Apply a layer of the BMS 5-95 sealant to the bolt, washer, nut and cotter pin.
S 434-014
(5)
Connect the rod end for the actuator piston rod to the spoiler panel:
(a)
Apply a layer of the BMS 3-24 grease to the bolt.
(b)
Install the bolt with the head left.
(c)
Install the washers and nut on the bolt.
(d)
Tighten the nut to 350-400 pound-inches.
(e)
Install the cotter pin.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-61-51
ALL ú ú 02 Page 405 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
(f) Apply the BMS 3-24 grease to the bolt washer, nut and cotter pin.
S 864-015
(6)
Supply the electrical power (Ref 24-22-00/201).
S 864-016
(7)
Supply the systems A and B hydraulic power (Ref 27-61-00/201).
S 874-017
(8)
Move the speed brake lever to bleed the spoiler actuators.
S 794-018
(9)
Make sure there are no leaks at the hydraulic lines.
F.
Examine the Clearance Between the Spoiler and the Flap
S 864-019
(1) Move the speed brake lever to the UP position to lift the spoilers.
NOTE: With the spoilers up, the trailing edge flaps will not hit
____ the spoilers during the retraction of the flaps.
S 864-020
(2)
Move the flap control lever to the UP detent to fully retract the trailing edge flaps.
S 864-021
(3)
Remove the systems A and B hydraulic power (Ref 27-61-00/201).
S 864-022
(4)
Move the speed brake lever to the DOWN position.
S 224-023
(5)
Do a check of the clearance between the spoiler and the flap without the hydraulic power (Fig. 402):
(a)
Manually lower the spoiler panel until the actuator piston is fully retracted.
(b)
Make sure the clearance between the rub strip on the spoiler and the flap is 0.03 to 0.13 inch at the closest point.
S 824-024
(6)
Adjust the clearance between the spoiler and the flap if it is not in the tolerance:
(a)
Supply the systems A and B hydraulic power (Ref 27-61-00/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-61-51
ALL ú ú 02 Page 406 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 飞行操纵 FLIGHT CONTROLS 5(65)
