NOTE: You can apply the vacuum source to the drain fittings or the
____
pitot-static probe ports.
S 485-005
(5)
Seal all of the static ports for the auxiliary system that are not used:
(a)
Make sure that you can fully remove the seal.
S 865-006
(6)
Make sure the flap control lever is in a position of less than 30-units.
S 865-007
(7)
Make sure these circuit breakers are closed:
(a)
P6 Panel
1) FLAP LOAD RELIEF
S 215-008
(8)
Make sure the LOAD LIMITER TEST LIGHT on the equipment bay light panel in the electronics compartment is off.
E.
Do the Test of the Airspeed Switches
S 725-009
(1)
Move the flap load limiter test switch on the equipment bay light panel in the electronics compartment to the SWITCH TEST position and hold it.
(a)
Make sure the green LOAD LIMITER TEST LIGHT comes on.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH AIRSPEED SWITCHES ú
27-51-89
ú ú 01 Page 502 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
S 725-010
(2) Pressurize the pitot-static system until the differential pressure is 1.121 inches Hg (152 knots) to 1.274 inches Hg (162 knots).
NOTE: Apply the pitot pressure to one system at a time.
____
(a) Make sure the LOAD LIMITER TEST LIGHT is off.
S 725-011
(3)
Decrease the differential pressure in the pitot-static system until the differential pressure is 1.046 inches Hg (147 knots) to 1.197 inches Hg (157 knots).
(a)
Make sure the LOAD LIMITER TEST LIGHT is on.
S 725-012
(4)
Release the test switch.
(a)
Make sure the LOAD LIMITER TEST LIGHT is off.
S 725-013
(5)
Do the test for the other airspeed switch.
F.
Put the Airplane Back to Its Usual Condition
S 865-014
(1)
Release the pressure in the pitot-static system.
S 085-015
(2)
Remove the pitot-static test equipment.
S 085-016
(3)
Remove the covers from the static ports.
NOTE: Make sure there is no dirt around the static ports.
____
S 865-017
(4) Remove the electrical power (Ref 24-22-00/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH AIRSPEED SWITCHES ú
27-51-89
ú ú 01 Page 503 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
FLAP 40-UNIT SWITCHES - REMOVAL/INSTALLATION
____________________________________________
1. General_______
A. There are two tasks in this procedure. There is a task for the removal and a task for the installation of the flap 40-unit switches.
B. The flap 40-unit switches are installed in the control stand. The switches operate on a cam on the drum of the flap handle assembly. It is necessary to remove the right stabilizer trim wheel and the door from the control stand to get access to the switches.
TASK 27-51-94-004-001
2. Flap 40-Unit Switches Removal (Fig. 401)_____________________________
A. Access
(1)
Location Zone
101, 102 Control Cabin
B.
Procedure
S 864-002
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 飞行操纵 FLIGHT CONTROLS 5(6)
