(3)
27-62-34/401, Speed Brake Arming Switch
(4)
27-62-37/401, Speed Brake Lever Position Sensor
D.
Access
(1)
Location Zone
101 Control Cabin - Left
102 Control Cabin - Right
202 Lower Nose Compartment
(2)
Access Panel
1103 Forward Access Door
3104 Forward Nose Wheel Well Panel
E.
Procedure
S 424-013
(1)
Install the lever brake (Fig. 401):
(a)
Adjust the backlash in the lever brake: 1) Measure the primary backlash in the lever brake. 2) If the primary backlash is not in the limit of 0.020 to
0.023 inch, adjust the backlash: a) Measure the total secondary backlash clearance on the brake shoe assembly.
b) Install two shims in the clearance for the secondary backlash to make sure the drive arm and brake shoe are in the center.
NOTE: Do not adjust the setscrews for the secondary
____ backlash. The thickness of each of the two shims must be 1/2 of the total secondary backlash clearance.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-62-21
ALL ú ú 02 Page 406 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
SEE A
SPOILER
MIXER
SPEED BRAKE
CONTROL
CABLES
SPOILER RATIO
CHANGER
SEE B
FWD
A
FWD
SPEED BRAKE INPUT QUADRANT
RATIO CHANGER B
Spoiler Mixer and Ratio Changer Rig Pin Location
Figure 403
CABLE SBA
CABLE SBB
WHEEL WELL FORWARD WALL
RIG PIN S/B-2
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-62-21
ALL ú ú 01 Page 407 ú Nov 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
c) Adjust the setscrews for the primary backlash until the total clearance is 0.020 to 0.023 inch divided equally between the two brake shoe assemblies.
NOTE: Make sure you do not compress the springs and
____ the brake shoes when you measure the clearance.
d) Remove the two shims from the brake shoe assembly.
(b)
Apply a thin layer of the petrolatum to the inner and outer parts of the friction quadrant.
(c)
Install the lever brake assembly: 1) Put the bearings and bearing retainers on the ends of the shaft. 2) Put the lever brake assembly and the shaft in their position in the airplane. 3) Apply a layer of the primer to the bolts for the bearing
retainers. 4) Install the eleven bolts in the two bearing retainers. 5) Install the washers and nuts on the bolts. 6) Install the locknut to attach the lever brake input arm to
the shaft.
(d) Attach the lower control rod to the input arm for the lever brake: 1) Install the bolt with the head inboard. 2) Install the washer and nut on the bolt.
S 024-014
(2)
Install the forward drum:
(a)
Install the washer on the shaft.
(b)
Install the forward drum quadrant on the shaft.
NOTE: The shaft and the quadrant have a tooth that is not
____ there to make sure the quadrant is in the correct position.
(c)
Install the washer and the quadrant retaining bolt.
(d)
Tighten the quadrant retaining bolt to 40-50 pound-inches.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-62-21
ALL ú ú 01 Page 408 ú Mar 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
(e) Install the lockwire on the quadrant retaining bolt and the forward drum quadrant.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 飞行操纵 FLIGHT CONTROLS 5(112)
