27-51-00
ALL ú ú 02 Page 11 ú Mar 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
G. The angle of flap extension is measured relative to the wing chord plane. When the flaps are fully retracted, the trailing edge of the aftflap is aligned with the wing chord plane. When the flaps are extended to 40 units, the angle between the wing chord plane and the midflap is approximately 43 degrees. Since the aftflap moves relative to the midflap, the aftflap rotates to an angle of approximately 69 degrees from the wing chord plane.
3. Flap Tracks and Fairings
________________________
A. The flap tracks are curved forged steel beams mounted on the lower surface of the wing. A flap transmission assembly is mounted on each flap track (Fig. 6). The tracks and the transmission assemblies are housed in aerodynamic fairings.
B. Each outboard flap track is contained in a two piece fairing made from aluminum frames covered with graphite reinforced kevlar skins. The forward section of the fairing is rigidly attached to the wing. The aft fairing section rotates about a hinge support mounted on the main flap track. Two fairing actuator tracks and an aft flap sequencing track are mounted in the aft fairing section. Rollers on a support arm on the midflap carriage engage in the two fairing actuator tracks. The tracks act as cams to rotate the aft fairing downward as the outboard flap extends. A retractable landing light mounted in the aft outboard fairing extends as the fairing rotates downward. The aftflap sequencing track is used as a cam for the aftflap actuating mechanism. The rear portion of the aft fairing is detachable.
C. The tracks for the inboard flap are contained in fixed fairings. The inboard flap outboard track is contained in the flap track fairing. The inboard flap inboard track is contained in the wing-to-body fairing. Torque tubes between the midflap carriages and the midflap pass through openings in the fairings. The openings are curved slots which allow fore and aft motion of the midflap. The inboard flap outboard track fairing (Ref Chapter 54) has a closure door to seal the opening when the flaps are retracted. The door is located at the aft end of the opening. The door is opened by pressure from the carriage torque tube when the flaps are extended.
4. Flap Control Lever
__________________
A. A flap control lever located on the upper right side of the control stand regulates the position of the trailing edge flaps (Fig. 7). The lever assembly consists of a spring-loaded telescoping handle and a cable drum. The cable drum rotates around a shaft in the control stand. A flap control cable attaches to the cable drum. The lever rotates around a quadrant which has detents at the flap positions. The lever is spring loaded to lock in each detent. Lifting the lever about 1/4 inch releases the lock and allows rotation. The quadrant contains gates at the 1- and 15-unit detents which prevent inadvertent lever movement past the detent position. The lever must be lowered into the detent and passed under the gate before further rotation can occur. The flap control lever actuates the cable system to drive a cable drum and flap control quadrant in the right wheel well.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-00
ALL ú ú 02 Page 12 ú Mar 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
SEE A
TORQUE TUBE
UNIVERSAL JOINT
OUTBOARD MIDFLAP
FLAP TRACK TORQUE LIMITER HOUSING TRANSMISSION GEARBOX BALL NUT AND SCREW ACTUATOR FWD
INBD
A
Flap Transmission Assembly Figure 6
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-00
ALL ú ú 01 Page 13 ú Oct 25/84
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
FLAP CONTROL LEVER
FLAP QUADRANT CONTROL STAND
FWD
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 飞行操纵 FLIGHT CONTROLS 3(137)
