S 434-029
(16)
Install the cable guards (23 and 26):
(a)
Attach the aft cable guard (23) to the jackscrew gearbox (8) with two bolts, nuts, and washers.
NOTE: The spline adapter may be needed to get additional
____ slack to remove the initial cable coil.
CAUTION:_______MAKE SURE YOU INSTALL THE SUPPORT PLATE CORRECTLY. IF THE SUPPORT PLATE IS NOT INSTALLED CORRECTLY, THE AMOUNT OF TORQUE NECESSARY TO DISENGAGE THE MANUAL CLUTCH CAN EXCEED THE LIMITS.
(b) Attach the forward cable guards (26) and the support plate (25) to the jackscrew gearbox (8) with the bolts, washers and nuts.
NOTE: Make sure the bearing assembly and the washer (28)
____ are installed on the same side of the support plate (25) as the cable drum (24).
(c)
Attach the aft cable guard (23) to the support plate (25) with the bolt, nut, and washer.
(d)
Install the nut (27): 1) Torque the nut (27) finger tight. 2) Discard the old cotter pin and install a new cotter pin in
the end of the castellated nut.
S 824-025
(17)
Adjust the stabilizer trim cables STA and STB (AMM 27-41-00/501).
S 824-026
(18)
Adjust the stabilizer trim position indicator (AMM 27-41-00/501).
(19)
Remove the adapter from the jackscrew gearbox (8).
(20)
Do the test of the stabilizer clutch friction (AMM 27-41-00/501).
S 094-027
S 754-015
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-41-81
ALL ú ú 03 Page 414 ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 434-070
(21)
Install the primary stabilizer trim actuator (18) and the actuator cover (9) on the jackscrew gearbox (8):
S 434-069
(22)
Install the primary stabilizer trim actuator (18) and the actuator cover (9) on the jackscrew gearbox (8):
(a)
Make sure the mating surfaces of the actuator and the jackscrew gearbox are clean.
(b)
Clean the mating surfaces at the forward attach bolt for electrical bonding.
(c)
Engage the actuator splined shaft with the internal spline of the jackscrew gearbox (8).
(d)
Install the actuator mounting bolts (15) with the washers and the locknuts.
(e)
Install the cover bolts (19) for the actuator cover (9) with the bolt head down.
(f)
Install the wire bundle clamp to the bolt clip at the bolt (12).
(g)
Install the electrical connectors (11).
(h)
Make sure the electrical resistance between the actuator housing and the airplane structure is 0.010 ohm maximum.
S 864-020
(23)
Remove the DO-NOT-CLOSE tags and close these circuit breakers:
(a)
P6-2 Circuit Breaker Panel
1) STABILIZER TRIM ACTUATOR
2) STABILIZER TRIM CONT
(b)
P18-0 Circuit Breaker Panel
1) STABILIZER TRIM SERVO
S 414-021
(24)
Close the access doors 3701 and 1103.
S 724-023
(25)
Do the test of the stabilizer manual travel limits (AMM 27-41-00/501).
S 224-006
(26)
Do the test of the stabilizer trim auxiliary brake (AMM 27-41-00/501).
S 724-024
(27)
Do the test of the stabilizer trim wheel free movement (AMM 27-41-00/501).
(28)
Do the test of the electrical trim system (AMM 27-41-00/501).
S 224-004
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-41-81
ALL ú ú 03 Page 415 ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 224-007
(29) Do the test of the autopilot stabilizer trim servo (AMM 22-11-81/501).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 飞行操纵 FLIGHT CONTROLS 3(116)
