(b)
Install the four installation screws.
S 434-019
(2) Attach the cables to the MPCB:
(a) Remove the MPCB terminal cover.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
24-21-41
ALL ú ú 03 Page 409 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
(b)
Install the cables on the terminal studs.
1) Use the notes you made during the removal procedure to make the correct installation.
(c)
Install the nuts on the studs, and tighten to the torque values on the terminal cover.
CAUTION:_______BE CAREFUL WHEN YOU CONNECT THE CONNECTOR. DAMAGED PINS CAN CAUSE FAILURE OF THE CIRCUIT BREAKER.
(d)
Connect the electrical connector.
(e)
Install the MPCB terminal cover and tighten the two screws.
S 414-013
(3)
Install the two access panels, 3103 and 3105, on the right inner wall of the nose wheel well.
(a) Apply grease, D00015 to the hole of the washers and the fastener shanks before installing them.
(4)
Do this task: AC Generation - System Test (AMM 24-21-00/501).
S 734-021
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
24-21-41
ALL ú ú 02 Page 410 ú Mar 15/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
AC SYSTEM GENERATOR AND APU MODULE (P5-4) - REMOVAL/INSTALLATION
________________________________________________________________
1. General_______
A. This procedure has these tasks:
(1)
Removal of the AC System Generator and APU Module
(2)
Installation of the AC System Generator and APU Module
B.
The AC System Generator and APU Module, P5-4, is located on the P5 Overhead Panel in the flight compartment.
TASK 24-21-51-004-001
2. Removal of the AC System Generator and APU Module_________________________________________________
A. References
(1)
AMM 24-22-00/201, Electrical Power
B.
Access
(1)
Location Zone
211 Flight Compartment, Left
C.
Prepare for the Removal
S 864-007
(1)
Remove electrical power from the airplane (AMM 24-22-00/201).
D.
Procedure
S 014-002
(1) Do these steps to remove the module:
(a) Loosen the quarter turn fasteners on the module.
NOTE: Hold the module when you loosen the quarter turn
____ fasteners so that the module does not fall.
CAUTION:_______CAREFULLY REMOVE THE MODULE FROM THE OVERHEAD PANEL. IF YOU DO NOT, DAMAGE TO THE ELECTRICAL CABLES AT THE REAR OF THE MODULE CAN OCCUR.
(b)
Pull the module carefully out from the overhead panel to get access to the electrical connectors.
(c)
Disconnect the electrical connectors from the module.
(d)
Put protective covers on the electrical connectors.
TASK 24-21-51-404-003
3. Installation of the AC System Generator and APU Module______________________________________________________
A. References
(1)
AMM 24-22-00/201, Remove Electrical connectors.
(2)
AMM 24-22-00/201, Supply External Power
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
24-21-51
ALL ú ú 01 Page 401 ú Jul 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
B. Access
(1) Location Zone
211 Flight Compartment, Left
