(b)
Do the steps that follow to do a check of the retraction of the wing landing gear. 1) Quickly move the control lever to the UP position and into
the detent. 2) Measure the time that the EICAS lower display shows the A doors in the open position.
NOTE: Start to measure the time when the door open
____ indication comes into view for the wing landing gear.
3) Make sure the left (right) door open indication does not show for more than 15 seconds.
(c)
Move the control lever to the OFF position.
(d)
Do the steps that follow to do a check of the extension of the wing landing gear. 1) Quickly move the control lever to the DN position and into
the detent. 2) Make sure the left (right) door open indication does not show for more than 21 seconds. 3) Make sure the movement of the left (right) wing door is smooth and moves at a linear rate.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-32-00
ALL ú ú 01 Page 507 ú Oct 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 747-400 MAINTENANCE MANUAL
4) Make sure the time for the left (right) door for the wing landing gear to close is not more than 6 seconds.
NOTE:____ Do not use the EICAS indication to measure the door
close time. From the ground, measure the time for the doors to close. Start to measure the time when
the doors start to close.
(e) (f) (g) (h) Move the control lever to the UP position.Make sure the landing gear is up and locked. 1) Make sure the components attached to the landing gear do not interfere with the landing gear as it retracts.Move the control lever to the OFF position.Quickly do these steps in the sequence that follows: 1) Move the control lever to the DN position. 2) When the landing gear is in the half extended position, immediately move the control lever to the UP position.
NOTE:____ You must smoothly move the control lever from the DN position to the UP position in approximately 3 seconds.
(i) (j) (k) (l) (m) (n) (o) (p) (q) Make sure the direction of the landing gear changes.Make sure the landing gear goes to the retracted position. 1) Make sure the components attached to the landing gear do not interfere with the landing gear as it retracts.Make sure the landing gear doors close.Make sure there is no fluid leakage from the hydraulic system for the landing gear.Make sure there is no mechanical damage.Make sure the wing landing gear does not touch, hit, or catch on the landing gear doors.Move the control lever to the DN position when the gear UP indication shows on the top EICAS display.Make sure the landing gear is down and locked. 1) Make sure the components attached to the landing gear do not interfere with the landing gear as it extends.Quickly do these steps in the sequence that follows: 1) Move the control lever to the UP position. 2) When the landing gear is in the half retracted position, immediately move the control lever to the DN position.
NOTE:____ You must smoothly move the control lever from the UP position to the DN position in approximately 3 seconds.
(r) (s) Make sure the direction of the landing gear changes.Make sure that the landing gear goes to the down and locked position. 1) Make sure the components attached to the landing gear do not interfere with the landing gear as it extends.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-32-00
ALL ú ú 01 Page 508 ú Oct 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
(t)
Make sure the landing gear doors close.
(u)
Make sure there is no fluid leakage from the hydraulic system for the landing gear.
(v)
Make sure that there is no mechanical damage.
(w)
Make sure the wing landing gear does not touch, hit, or catch A on the landing gear doors.
(x)
Move the control lever to the OFF position after the gear DOWN indication shows on the top EICAS display.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：747-400 AMM 飞机维护手册 起落架 LANDING GEAR 4(54)
