FORWARD FACING MISMATCH:
0.04 FOR 75% OF SEAL LENGTH
0.06 FOR 25% OF SEAL LENGTH
AFT FACING MISMATCH:
0.04 FOR 75% OF SEAL LENGTH
0.09 FOR 25% OF SEAL LENGTH
ADJUST THE SEAL TO GET A SMOOTH SEAL DEPRESSION AS SHOWN.
MEASURE THE PROFILE IN LINE WITH ACTUATOR LINKAGE AT A POINT 3.0 INCHES AFT OF FLAP LEADING EDGE. THE FLAP PROFILE TO BE AS FOLLOWS (WITH A NEGATIVE PROFILE, THE FLAP BENDS IN AS SHOWN):
+0.01 TO -0.05 INCH (FLAPS NO. 1E THRU 9, 18 THRU 26E) +0.05 TO -0.05 INCH (FLAPS NO. 10 AND 17)
DIMENSIONS X AND Y ARE PERPENDICULAR DISTANCES FROM THE LOWER LEADING EDGE CHORD TO THE PIVOT POINT G.
FLAP CAVITY SEALS NOT INSTALLED ON WING STRUCTURE AFT OF FLAP PANELS NO. 5, 7, 20 AND 22.
MEASUREMENT IS TAKEN WITH EROSION SHIELD MOLDINGS BONDED IN THE FLAP ASSEMBLY. THE DIFFERENCE (WITH FLAPS RETRACTED) BETWEEN THE FLAP AND THE WING STRUCTURE MUST NOT BE LARGER THAN:
0.02 INCH FOR 75% OF SEAL LENGTH
0.04 INCH FOR 25% OF SEAL LENGTH
Variable Camber Flaps Gap and Mismatch Requirements
Figure 501 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-81-00
ALL ú ú 01 Page 502 ú Feb 15/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
Variable Camber Flaps Gap and Mismatch Requirements
Figure 501 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-81-00
ALL ú ú 01 Page 503 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
0.15 |0.05 INCH
FLAPS NO. 10 AND 17:
D-D
0.15 |0.25/-0.05 INCH AT INBD END, BECOME SLOWLY THINNER TO
0.15 |0.05 INCH AT OUTBD END
SEAL DEPRESSION
FLAP CAVITY AFT SEAL
G-G
F-F
Variable Camber Flaps Gap and Mismatch Requirements Figure 501 (Sheet 3)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-81-00
ALL ú ú 01 Page 504 ú Feb 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
NOTE:____ ON LANDING GEARS AND WITHOUT FUEL. MEASUREMENT IS TAKEN WITH AIRPLANE C-C OUTBD
Krueger Flaps Gap and Mismatch Requirements Figure 502 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-81-00
ALL ú ú 01 Page 505 ú Feb 15/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
WING LEADING EDGE
E
CLEARANCE
STRUCTURE INDICATOR PIN
0.10
INCH
0.04 RETRACT
RETRACT STOP BOLT
STOP
E
SEE A
KRUEGER
FLAP STOP BOLT
BRACKET
SEE B C WASHERS ACTUATOR ARM ON ROTARY
D-D E-E
SHIM
1
0.09 |0.03
2 1
INCH
A B
0.04 INCH
KRUEGER KRUEGER FLAP
MAXIMUM FLAP
0.05 INCH MAXIMUM
6-INCH 6-INCH
STRAIGHTEDGE STRAIGHTEDGE
1.75
INCHES 1.75
1.25 INCHES
1.25
POSITIVE CONTOUR AT FLAP LINKAGE
NEGATIVE CONTOUR AT FLAP LINKAGES
CC
Krueger Flaps Gap and Mismatch Requirements Figure 502 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-81-00 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：747-400 AMM 飞机维护手册 飞行操纵 FLIGHT CONTROLS 7(58)
