21-51-06
ALL ú ú 02 Page 511 ú Mar 15/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
(d)
Push in and release the TRIP RESET switch. 1) Make sure the conditions above stay unchanged.
(e)
Remove the jumper from the D528 electrical connector.
(f)
Connect the D528 electrical connector to the Right Engine Bleed Air Overheat switch.
(g)
Push in and release the TRIP RESET switch.
1) Make sure these lights go OFF: a) R BLEED TRIP OFF (P5-10 Panel) b) AIR COND (P7 Glareshield)
(h)
Set the Engine 2 BLEED switch to the OFF position. 1) Make sure the DUAL BLEED light goes OFF.
(i)
Set the APU BLEED switch to the OFF position.
E. Put The Airplane Back To Its Usual Condition
S 415-024
(1)
Install and/or close the access panels which you opened for this test.
S 865-022
(2)
Remove the pneumatic power from the airplane if it is not necessary (Ref 36-05-00/201).
S 865-023
(3)
Remove the electrical power from the airplane if it is not necessary (Ref 24-22-00/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
21-51-06
ALL ú ú 02 Page 512 ú Mar 15/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
AIR CYCLE MACHINE (ACM) - UNIT SERVICING
________________________________________
1. General_______
A. This task replaces the oil in the air cycle machine. Refer to 12-13-51/301, Air Cycle Machine, to make sure the oil level is correct.
TASK 21-51-11-603-001
2. Air Cycle Machine Oil Replacement (Fig. 301)_________________________________
A. Standard Tools and Equipment
(1) Container for unwanted material - capacity of 1 gallon
B. Consumable Materials
(1) Lubricant - Oil, as approved by Garrett Corporation, 9851-9951 Sepulveda Boulevard, Los Angeles, California 90009, or one these below (Ref 20-30-21/201):
(a)
D00068 MIL-L-23699
(b)
D00071 MIL-L-7808G
C. Access
(1)
Location Zones
212 Left Air Conditioning Equipment Bay
214 Right Air Conditioning Equipment Bay
(2)
Access Panels
3303L Air Conditioning Access Panel
3403R Air Conditioning Access Panel
D. Procedure
S 013-003
(1)
Open the access doors to the air conditioning bay.
S 613-004
(2)
Do these steps to replace the oil for the air cycle machine:
(a)
Hold the container below the drain plug on the bottom of the oil sump.
(b)
Remove the drain plug and let the oil drain fully.
(c)
Remove the chip detector plug from the drain plug.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
21-51-11
ALL ú ú 02 Page 301 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
CAUTION: THE CHIP DETECTOR PLUG SHOULD NOT HAVE ANY METAL PARTICLES
_______ ON IT. THE PRESENCE OF METAL PARTICLES IS A SIGN OF WEAR IN THE AIR CYCLE MACHINE AND OF POSSIBLE ACM FAILURE.
(d)
Inspect the chip detector plug for metal particles.
(e)
Clean the chip detector plug and install it with a new O-ring into the drain plug.
(f)
Install the drain plug with a new O-ring in the bottom of the oil sump.
(g)
Fill the air cycle machine with oil until the oil level in the sight glass is three-fourths full.
NOTE: The oil sump holds approximately 300 cubic centimeters
____
of oil.
Loose wires can possibly come out of the filler port when you remove the filler plug. This condition is satisfactory. Put the wires in the filler port before you install the filler plug. 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：737-300 400 500 AMM 飞机维护手册 空调 AIR CONDITIONING 2(14)
