-
the centerline of the feedback attachment hole of the
bellcrank lever. 1) If there is no gap, make the cable shorter.
NOTE: To do this, loosen the jamnut and turn the rod end
____ bearing.
(g) Do a check that the threads are sufficiently engaged.
NOTE: To do this, make sure a 0.032 inch (0.80 mm) diameter
____ lockwire does not go through the witness hole.
1) If the threads are not correctly engaged, adjust the cable length. Do the steps to check the cable length at the bellcrank end.
NOTE: To do this, turn the rod end bearing.
____
(h)
If adjustment of the rod end bearing was necesary, tighten the jamnut against the rod end bearing to 24-27 pound-inches (2.7-3.1 Newton meters).
(i)
Attach the rod end bearing to the bellcrank lever arm.
1) ENGINES POST-CFMI-SB 72-667; (ENGINES WITH ROD-END BEARINGS WITH DROP-IN UNIBALLS); Lubricate the uniballs on the rod end bearing. a) Lubricate the two sides of the uniballs on the rod end
bearing with LPS-1 penetrating oil.
1. Let the uniballs soak in the oil for 2-3 minutes.
_
b) Turn the uniballs back and forth in the two directions fully three times, until there is a smooth operation of the uniballs.
1. If more oil is necessary for smooth operation, do
_ the above steps again. c) Wipe off all unwanted oil with a lint free cloth.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
75-31-02
ALL ú ú C01.1 Page 511 ú Jul 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
d) Put the rod end bearing in position on the outboard side of the lever arm.
2) ENGINES PRE-CFMI-SB 72-667; (ENGINES WITH ROD-END BEARINGS WITH UNIBALLS STAKED IN WITH TEFLON SLEEVES); Put the rod end bearing in position on the outboard side of the lever arm.
3) Install the washer and the bolt (put the bolt head away
from the compressor case).
4) Install the slotted nut.
5) Tighten the nut to 20-40 pound-inches
(2.3-4.5 Newton meters) while you align the nut slot with the cotter pin hole.
NOTE: Replace the nut if you cannot get the minimum torque
____ value, or if you get more than the maximum torque value.
6) Install a cotter pin.
7) Bend the ends of the pin around the nut flats.
S 725-011-C00
(4) Do a check for the cable length at the MEC end (AMM 75-31-00/201).
(a)
Make sure the VSV system is in the full open position.
(b)
Use a lockwire to attach a pull scale to the rod end bearing at the MEC end.
(c)
Apply a tension load of 15-17 pounds (67-76 N) in a line with the cable centerline axis.
(d)
Keep the load while you push the MEC feedback arm away from the cable attachment bracket.
(e)
Do a check for the clearance between the items that follow:
-
the centerline of the rod end bearing of the cable
-
the centerline of the cable attachment hole of the MEC
feedback arm. 1) If there is no clearance, make the cable shorter.
NOTE: To do this, loosen the jamnut and turn the rod end
____
bearing.
(f)
Operate the VSV system to the full closed position.
(g)
Attach a pull scale to the rod end bearing and apply a tension load of 15-17 pounds (67-76 N).
NOTE: Do this in a line with the cable centerline axis.
____
(h) Keep the load while you push the MEC feedback arm to the cable attachment bracket.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
75-31-02
ALL ú ú C01 Page 512 ú Jul 12/00
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 空气 AIR(67)
