(g)
Move the rig plate until its rig line aligns with the rig pointer.
(h)
Tighten the screws to 7-9 pound-inches (0.8-1.0 Newton meters).
(i)
Examine the rig alignment after you tighten the screws.
E. Put the airplane back to its usual condition
S 085-081-C00
(1)
Use the instructions in the SPS Users Manual to remove the VSV
position/N2 indicator.
S 865-082-C00
(2)
For the applicable engine, open this circuit breaker and attach a
DO-NOT-CLOSE tag:
(a) P6 Load Control Center
1) AIRPLANES WITHOUT THE EIS SYSTEM;
-N2 TACH IND
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
75-31-00
ALL ú ú C06 Page 544 ú Mar 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
2) AIRPLANES WITH THE EIS SYSTEM; - EIS PRI2 - EIS PRI4
(3) S 085-083-C00Use the instructions in the SPS Users Manual to remove the VSV position transmitter.
(4) S 865-084-C00For engine No. 1, remove the DO-NOT-CLOSE tag and close this circuit breaker: (a) P6 Load Control Center 1) AIRPLANES WITHOUT THE EIS SYSTEM; - N2 TACH IND 2) AIRPLANES WITH THE EIS SYSTEM; - EIS PRI2 - EIS PRI4
(5) S 865-096-C00For engine No. 2, remove the DO-NOT-CLOSE tag and close this circuit breaker: (a) P6 Load Control Center 1) AIRPLANES WITHOUT THE EIS SYSTEM; - N2 TACH IND 2) AIRPLANES WITH THE EIS SYSTEM; - EIS PRI2 - EIS PRI4
(6) S 415-085-C00Close the thrust reversers (AMM 78-31-00/201)
(7) S 415-086-C00Close the fan cowl panels (AMM 71-11-02/201)
(8) S 795-087-C00Do an idle leak check (AMM 71-00-00/501, Test No. 3).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
75-31-00
ALL ú ú C07 Page 545 ú Mar 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
VARIABLE STATOR VANE ACTUATOR - REMOVAL/INSTALLATION
____________________________________________________
1. General
_______
A. This procedure gives removal and installation instructions for the variable stator vane (VSV) actuator.
B. There are two VSV actuators attached to the forward stator case of the high pressure compressor (HPC). They are found at the 1:30 and 7:30 o'clock positions. Differences in the installation instructions between the left and right VSV actuators are given in the procedure.
C. The removal and installation procedures for the VSV actuators on the
CFM56-3-B1/-3B-2 engines are given in tasks 2 and 3. Procedures for the ú CFM56-3C-1 and CFM56-3-B1/-3B-2/-3C-1 with 3-D Aero HPC (Post-CFMI-SB ú 72-982) are given in tasks 4 and 5. ú D. AIRPLANES WITH CFM56-3-B1/-3B-2 ENGINES (PRE-CFMI-SB 72-982; ú CFM56-3-B1/-3B-2 VSV actuators are not equipped with an actuator clevis. ú The acutuator clevis is part of the bellcrank assembly. Thus, the ú actuator has a shorter stroke than the other CFM56-3C-1 engines. ú E. AIRPLANES WITH CFM56-3C-1 ENGINES (PRE AND POST-CFMI-SB 72-982) AND ú CFM56-3-B1/-3B-2 ENGINES (POST-CFMI-SB 72-982); ú These engines are equipped with an actuator clevis attached to the rod ú end. The actuator clevis to rod end is not field adjustable. Thus, the ú rigging of the actuator to the bellcrank assembly is not necessary. ú (1) There are two VSV actuator configurations for the CFM56-3C-1 ú (Fig. 401): ú CONFIGURATION 1 (PRE-CFMI-SB 75-023); ú This actuator does not have a lock nut or key lock on the actuator ú clevis end. ú CONFIGURATION 2 (POST-CFMI-SB 75-023); ú A new VSV actuator was introduced with a thinner piston rod ú diameter, a non-field adjustable threaded rod end, and a new end ú cap. This actuator has a lock nut or key lock on the actuator ú clevis end. ú (a) The Configuration 1 VSV actuator is completely interchangeable ú with the Configuration 2 VSV actuator, but only if installed in ú pairs with same part number.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 空气 AIR(49)
