(i)
ENGINES POST-CFMI-SB 75-014; Indications of air leakage at the flange. 1) If an indication is found, replace the C-seal flange gasket
(AMM 75-33-01/401).
S 216-004-C00
(3) Do a visual inspection of the CBP air tube and fittings and look for the items that follow:
(a)
Cracks, wear-through (caused by chafing), flat parts,
deformation and kinks.
1) If one or more of these are found, replace the tube
(AMM 75-33-01/401).
(b)
If an indication of air leakage at the tube coupling nut or
nipple is found, do the steps that follow:
1) If a loose coupling nut is found, tighten and torque the
nut to 135-150 pound-inches (15-17 Newton meters).
2) Install the lockwire from the nut to the sensor nipple.
3) If an indication of air leakage is found at the sensor,
replace the seal.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
75-33-00
ALL ú ú C02 Page 603 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
S 416-008-C00 WARNING: OBEY THE INSTRUCTIONS IN AMM 78-31-00/201 TO CLOSE THE THRUST
_______ REVERSERS. IF YOU DO NOT OBEY THE INSTRUCTIONS, INJURY TO PERSONS OR DAMAGE TO THE EQUIPMENT COULD OCCUR.
(4) Close the thrust reverser halves (AMM 78-31-00/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
75-33-00
ALL ú ú C01 Page 604 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
BLEED BIAS SENSOR - REMOVAL/INSTALLATION
________________________________________
1. General_______
A. This procedure contains two tasks.
(1)
The first task is to remove the Bleed Bias Sensor.
(2)
The second task is to install the Bleed Bias Sensor.
B. The sensor is found between the 9th-stage duct flange and the 9th-stage
high pressure compressor (HPC) bleed port at the 4 o'clock position.
TASK 75-33-01-004-001-C00
2. Remove the Bleed Bias Sensor____________________________
A. References
(1) AMM 78-31-00/201, Thrust Reverser System
B. Access
(1)
Location Zones
506 Engine No. 1
606 Engine No. 2
(2)
Access Panels
5739L/5738L Engine No. 1 - Thrust Reverser Half
5839R/5838R Engine No. 2 - Thrust Reverser Half
C. Procedure (Fig. 401)
S 014-024-C00
WARNING: OBEY THE INSTRUCTIONS IN AMM 78-31-00/201 TO OPEN THE THRUST
_______ REVERSER. IF YOU FAIL TO DO SO, INJURY TO PERSONS AND DAMAGE TO EQUIPMENT CAN OCCUR.
(1)
Open the fan duct cowl and thrust reverser halves
(AMM 78-31-00/201).
S 034-003-C00
(2)
Disconnect the compressor bleed pressure (CBP) air tube from the bleed bias sensor.
S 034-020-C00
(3)
Remove couplings at 3 and 8 o'clock parting flanges on the 9th-stage bleed duct.
S 034-005-C00
(4)
Remove the coupling seals and keep them for the installation procedure.
S 034-006-C00
(5)
Remove the bolts and washers that attach the 9th-stage duct flanges to the HPC bleed ports on the combustion case at the 4 and 8 o'clock positions.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
75-33-01
ALL ú ú C02 Page 401 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 空气 AIR(124)
