曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
727.00 - Right
G. Flap Power Drive Unit Installation
SUBTASK 27-51-51-860-004
(1) Make sure that this circuit breaker is open and has safety tag:
F/O Electrical System Panel, P6-2
Row Col Number Name
D 13 C00841 FLIGHT CONTROL ALTN T.E. FLAP DRIVE
SUBTASK 27-51-51-860-005
(2) Make sure the flaps are in the retracted position.
SUBTASK 27-51-51-420-001
(3) If they are not installed, install the cables [6] on the power drive unit [21]:
(a) Put the cables [6] in their position on the cable drum [34].
(b) Install the pins [33] to attach the cables [6] to the cable drum [34].
SUBTASK 27-51-51-820-001
(4) Make sure the cables [6] and the cable drum [34] are in the correct position:
(a) Turn the power drive unit [21] until the black rig marks on the cable drum [34] align with the
white cable guard [11] on the power drive unit [21].
(b) Make sure the lower cable [6] wraps around the cable drum [34] 2 to 2 1/2 turns.
NOTE: This is cable WFFA.
(c) Make sure the upper cable [6] wraps around the cable drum [34] 0 to 1/2 turns.
NOTE: This is cable WFFB.
SUBTASK 27-51-51-420-002
(5) Install the power drive unit [21]:
(a) Put the power drive unit [21] in its position on the structure.
(b) Apply compound, C00913 to the shank and threads of the bolt [7] and bolts [14].
(c) Install the bolt [7], bolts [14], washers [8], washers [9] and nuts [10] to attach the power
drive unit [21].
SUBTASK 27-51-51-420-003
(6) Connect the cables [6] to the cables [2] for the flap control unit [23]:
(a) Connect the cables [2] and cables [6] at the turnbuckles [4].
(b) Remove the labels from the cables [2].
(c) Tighten the cables [2] to 125 ±10 pounds (556 ±45 newtons).
NOTE: This is an initial cable tension. The cables [2] will be adjusted to their final tension
during the trailing edge flap control system adjustment.
(d) Install the locking clips [3] on the turnbuckles [4].
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-51
Page 410
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
SUBTASK 27-51-51-420-004
(7) Connect the torque tubes [12] to the power drive unit [21]:
NOTE: Do not rotate the torque tubes more than 5 spline teeth, in either direction, to the
nearest position where the bolt holes align at the torque tube coupling connection. Do
not rotate the PDU at this step.
(a) Apply grease, D00633 to the coupling sleeve [36].
(b) Put the splined couplings [37] in the coupling sleeves [36].
(c) Install the screws [35] to attach the coupling sleeves [36] to the splined couplings [37].
(d) Install lockwire on the screws [35].
SUBTASK 27-51-51-420-005
(8) Connect the jumper wire [13] for the electric motor [19]:
(a) Install the screw [15], washers [16] and nut [17] that attach the jumper wire [13].
(b) Make sure the resistance between the jumper wire [13] and the electric motor [19] is less
than 0.4 milliohms.
NOTE: When you measure the resistance, the probe can be closer than 0.25 inches (6.4
millimeters) to the jumper terminal.
(c) Put a fillet seal of sealant, A02315 or sealant, A00247 around the two ends of the screw [15].
SUBTASK 27-51-51-080-001
(9) Remove the clamp set, SPL-1726 from the torque tubes [12].
SUBTASK 27-51-51-420-006
(10) Connect the hydraulic lines [1] and the case drain line [20] to the hydraulic motor [22]:
(a) Remove the plugs from the ports on the hydraulic motor [22].
(b) Remove the caps from the hydraulic lines [1].
(c) Connect the hydraulic lines [1] to the hydraulic motor [22].
(d) Remove the cap from the case drain line [20].
(e) Connect the case drain line [20] to the power drive unit [21].
SUBTASK 27-51-51-420-007
(11) Connect the electrical connector [18] to the electric motor [19].
(12) Do this task:Trailing Edge Flap Power Drive Unit Servicing, TASK 12-22-51-610-801.
SUBTASK 27-51-51-820-002
(13) Do this task: Trailing Edge Flap Control System Adjustment, TASK 27-51-00-820-801.
NOTE: This adjustment will include the final adjustment of the cables WFFA and WFFB.
SUBTASK 27-51-51-080-002
(14) Remove the rig pin from the flap control unit [23]:
SUBTASK 27-51-51-820-003
(15) Do this task: Trailing Edge Flap Drive System Adjustment, TASK 27-51-00-820-802.
SUBTASK 27-51-51-640-001
(16) Lubricate the torque tube couplings. To lubricate the couplings, do this task: Trailing Edge Flap
Torque Tube and Torque Tube Support Lubrication, TASK 12-22-51-640-801.
SUBTASK 27-51-51-410-001
(17) Install the lower pan [25] on the flap control unit [23]:
737-600/700/800/900
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
737-600-700-800-900 飞机维护手册5 AIRCRAFT MAINTENANCE MANUA(75)
