曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
27-51-00-440-801 Trailing Edge Flap System Reactivation (P/B 201)
27-51-00-860-804 Retract the Trailing Edge Flaps (P/B 201)
27-51-28-400-802 Outboard Flap Outboard Support Aft Fairing Installation (P/B 401)
27-51-28-400-804 Outboard Flap Inboard Support Aft Fairing Installation (P/B 401)
C. Tools/Equipment
Reference Description
STD-4233 Pin, Rig, 0.3125 in (7.938 mm)
D. Consumable Materials
Reference Description Specification
D00633 Grease - Aircraft General Purpose BMS3-33
E. Expendables/Parts
AMM Item Description AIPC Reference AIPC Effectivity
2 Rod assembly 27-51-24-01-075 GUN ALL
27-51-24-01-080 GUN ALL
27-51-24-01-090 GUN ALL
27-51-24-01-095 GUN ALL
8 Pin 27-51-24-01-010 GUN ALL
15 Pin 27-51-24-01-010 GUN ALL
16 Rod assembly 27-51-24-01-070 GUN ALL
27-51-24-01-085 GUN ALL
17 Bellcrank assembly 27-51-24-01-180 GUN 001-012, 101,
155-157, 201-999
27-51-24-01-182 GUN 001-012, 101,
155-157, 201-999
27-51-24-01-350 GUN 001-012, 101,
155-157, 201-999
27-51-24-01-352 GUN 008-099, 101-122,
155-157
27-51-24-01-355 GUN 001-012, 101,
155-157, 201-999
24 Pin 27-51-24-01-010 GUN ALL
25 Rubcap 27-51-24-01-150 GUN ALL
F. Location Zones
Zone Area
567 Left Wing - Outboard Flap
667 Right Wing - Outboard Flap
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-24
Page 406
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
G. Prepare for the Installation
SUBTASK 27-51-24-820-001
(1) Make sure the bellcrank assembly [17] is the correct length:
NOTE: The length of the bellcrank assembly [17] can be changed to adjust for lateral trim
problems.
(a) Measure the distance between the center of the bolt hole in the adjustment fitting [36] and
the bellcrank assembly [17].
NOTE: This distance is referred to as Dimension A.
(b) Make sure the Dimension A on the bellcrank assembly [17] you will install is the same as
the bellcrank assembly [17] that you removed.
NOTE: The nominal dimension of the inboard bellcrank assembly [17] is 14.56 inches
(36.98 cm). The nominal dimension of the outboard bellcrank assembly [17] is
13.74 inches (34.9 cm).
1) If the inboard and outboard bellcrank assembly [17] are not at the nominal length, they
should both be the same distance from the nominal dimension.
(c) If the bellcrank assembly [17] is not the correct length, adjust the bellcrank assembly [17]:
1) Loosen the nuts [35] on the adjustment fitting [36] until the locking washer [34] is
disengaged from the bellcrank assembly [17].
2) Change the position of the adjustment fitting [35].
3) Engage the locking washer [34] with the bellcrank assembly [17].
4) Tighten the nuts [35] on the adjustment fitting [31].
5) Install lockwire on the nuts [35].
H. Outboard Aft Flap Actuating Mechanism Installation
SUBTASK 27-51-24-420-001
(1) Install the bellcrank assembly [17] on the carriage [18]:
(a) Apply grease, D00633 to the shank of the bolt [29].
NOTE: Make sure you do not get grease, D00633 on the threads of the bolt [29].
(b) Install the bolts [28] in the bellcrank assembly [17].
(c) Put the bellcrank assembly [17] in its position on the carriage [18].
(d) Install the bolt [29] and washer [30] that attach the bellcrank assembly [17] to the carriage
[18].
(e) Carefully clean all of the grease, D00633 from the threads of the bolt [29].
(f) Install the washer [31] and nut [32] on the bolt [29].
GUN 013-099, 102-122; GUN 001-012, 101, 155-157, 201-999 POST SB 737-57-1278
(g) Tighten the nut [32] to 760-840 pound-inches (96-121 newton-meters).
GUN 001-012, 101, 155-157, 201-999 PRE SB 737-57-1278
(h) Tighten the nut [32] to 240-410 pound-inches (27-46 newton-meters).
GUN ALL
(i) Install the pin [33] in the nut [32].
(j) Attach the rubcap [25] to the bellcrank assembly [17] with the washers [27] and nuts [26].
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-24
Page 407
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
SUBTASK 27-51-24-420-002
(2) Connect the aft rod assembly [2] and the forward rod assembly [16] to the bellcrank
assembly [17]:
(a) Apply grease, D00633 to the shank of the bolts [3] and the inside of the bushings [5].
NOTE: Make sure you do not get grease, D00633 on the threads of the bolts [3].
(b) Install the bolts [3], washers [4] and bushings [5] to attach the aft rod assembly [2] and the
forward rod assembly [16] to the bellcrank assembly [17].
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
737-600-700-800-900 飞机维护手册5 AIRCRAFT MAINTENANCE MANUA(15)
