曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
Page 604
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Outboard Flap Outboard Carriage Wear Limits
Figure 601 (Sheet 1 of 4)/27-51-23-990-803
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-23
Page 605
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Outboard Flap Outboard Carriage Wear Limits
Figure 601 (Sheet 2 of 4)/27-51-23-990-803
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-23
Page 606
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Outboard Flap Outboard Carriage Wear Limits
Figure 601 (Sheet 3 of 4)/27-51-23-990-803
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-23
Page 607
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Outboard Flap Outboard Carriage Wear Limits
Figure 601 (Sheet 4 of 4)/27-51-23-990-803
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-23
Page 608
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
TASK 27-51-23-200-802
3. Outboard Flap Inboard Carriage Inspection
(Figure 602)
A. General
(1) This task gives wear limits for the inboard carriage on the outboard flap.
(2) This task is applicable to the carriages at flap supports No. 2 and 7.
B. References
Reference Title
27-51-23-000-802 Outboard Flap Inboard Carriage Removal (P/B 401)
27-51-23-400-802 Outboard Flap Inboard Carriage Installation (P/B 401)
C. Tools/Equipment
Reference Description
STD-1096 Micrometer - Depth, 0-1 Inch, Readable to 1/1000 Inch
STD-1097 Caliper - Vernier, 0-6 Inch, Readable to 1/1000 Inch
D. Location Zones
Zone Area
543 Left Wing - Fairing Flap Support No. 2
643 Right Wing - Fairing Flap Support No. 7
E. Procedure
SUBTASK 27-51-23-020-020
(1) Do this task: Outboard Flap Inboard Carriage Removal, TASK 27-51-23-000-802.
SUBTASK 27-51-23-020-021
(2) Use these tools to do a check for wear on the part of the outboard flap inboard carriage:
(a) micrometer (0-1 Inch, readable to 1/1000 Inch), STD-1096
(b) readable to 1/1000 inch vernier 0 - 6 inch caliper, STD-1097.
SUBTASK 27-51-23-020-022
(3) Examine the parts of the outboard flap inboard carriage (Table 602):
(a) Remove the parts that you will measure.
(b) Measure the parts with a micrometer (0-1 Inch, readable to 1/1000 Inch), STD-1096 or a
readable to 1/1000 inch vernier 0 - 6 inch caliper, STD-1097.
(c) Compare the dimensions you measured with the permitted wear dimensions.
(d) If the parts are not in tolerance, replace or repair the parts.
Table 602/27-51-23-993-806
NAME OF THE PARTS
THAT ARE IN CONTACT
DIM.
DIAMETER DESIGN LIMITS WEAR LIMITS
MINIMUM
inches/mm
MAXIMUM
inches/mm
PERMITTED
MAXIMUM I.D./
MINIMUM O.D. OF
WORN PART
MAXIMUM
SERVICE
CLEARANCE
inches/mm
#1 BUSHING I.D. 1.3120 in 1.3130 in 1.3145 in
33.325 mm 33.350 mm 33.388 mm 0.0050 in
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-23
Page 609
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(Continued)
NAME OF THE PARTS
THAT ARE IN CONTACT
DIM.
DIAMETER DESIGN LIMITS WEAR LIMITS
MINIMUM
inches/mm
MAXIMUM
inches/mm
PERMITTED
MAXIMUM I.D./
MINIMUM O.D. OF
WORN PART
MAXIMUM
SERVICE
CLEARANCE
inches/mm
#1 PIN O.D. 1.3105 in 1.3115 in 1.3093 in 0.1270 mm
3.3287 mm 33.312 mm 33.256 mm
#2 ROLLER I.D. 1.3118 in 1.3125 in 1.3135 in
33.320 mm 33.338 mm 33.363 mm 0.0050 in
#2 PIN O.D. 1.3105 in 1.3115 in 1.3095 in 0.1270 mm
33.287 mm 33.312 mm 33.261 mm
#3 ROLLER O.D. 3.4365 in 3.4385 in 3.4345 in
87.287 mm 87.338 mm 87.236 mm
#4 BUSHING I.D. 1.2495 in 1.2505 in 1.2515 in
31.737 mm 31.763 mm 31.788 mm 0.0050 in
#4 PIN O.D. 1.2480 in 1.2490 in 1.2470 in 0.1270 mm
31.699 mm 31.725 mm 31.674 mm
#5 ROLLER I.D. 1.2493 in 1.2500 in 1.2515 in
31.732 mm 31.750 mm 31.788 mm 0.0050 in
#5 PIN O.D. 1.2480 in 1.2490 in 1.2470 in 0.1270 mm
31.699 mm 31.725 mm 31.674 mm
#6 ROLLER O.D. 3.4365 in 3.4385 in 3.4345 in
87.287 mm 87.338 mm 87.236 mm
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
737-600-700-800-900 飞机维护手册5 AIRCRAFT MAINTENANCE MANUA(12)
