曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
33 Beam assembly 27-51-28-01-460 GUN 001-028, 101-121,
155-157, 201-999
27-51-28-01-465 GUN 001-028, 101-121,
155-157, 201-999
40 Pin 27-51-28-01-220 GUN 001-028, 101-121,
155-157, 201-999
41 Link assembly 27-51-28-01-315 GUN 001-028, 101-121,
155-157, 201-999
42 Rod assembly 27-51-28-01-250 GUN 001-028, 101-121,
155-157, 201-999
48 Pin 27-51-28-01-285 GUN 001-028, 101-121,
155-157, 201-999
56 Pin 27-51-28-01-365 GUN 001-028, 101-121,
155-157, 201-999
67 Tailcone assembly 27-51-28-01-510 GUN 001-028, 101-121,
155-157, 201-999
E. Location Zones
Zone Area
544 Left Wing - Fairing Flap Support No. 1
644 Right Wing - Fairing Flap Support No. 8
F. Access Panels
Number Name/Location
544CL Flap Support No. 1 Access Cover
544CR Flap Support No. 1 Access Cover
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-28
Page 412
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(Continued)
Number Name/Location
544DR Flap Support No. 1 Access Door
644CL Flap Support No. 8, Access Cover
644CR Flap Support No. 8, Access Cover
644DL Flap Support No. 8, Access Door
G. Outboard Flap Outboard Support Aft Fairing Installation
SUBTASK 27-51-28-020-005
(1) If the fairing drive linkage is not installed on the aft fairing assembly [2], do these steps:
NOTE: The fairing drive linkage includes the drive rod assembly [32], adjust link assembly [41],
adjust rod assembly [42] and the attach beam assembly [33].
(a) Connect the adjust rod assembly [42] to the adjust link assembly [41]:
1) Install the bushing [45], bolt [43], washer [44], washer [46] and nut [47] that attach the
adjust rod assembly [42] to the adjust link assembly [41].
NOTE: For the left wing, install the bolt [43] with the head on the same side of the
adjust link assembly [41] as the bushing [45]. For the right wing, install the bolt
[43] with the head on the opposite side of the adjust link assembly [41] as the
bushing [45].
2) Install the pin [48] in the nut [47].
(b) Connect the adjust link assembly [41] to the attach beam assembly [33]:
1) Put the adjust link assembly [41] in its position on the attach beam assembly [33].
2) Install the bushing [51], bolt [49], washer [50], washer [52] and nut [53] to attach the
adjust link assembly [41] to the attach beam assembly [33].
3) Tighten the nut [53]:
a) Tighten the nut [53] to 370-475 pound-inches (41.8-53.7 newton-meters) if the bolt
[49] is not lubricated.
b) Tighten the nut [53] to 260-310 pound-inches (29.4-35.0 newton-meters) if the bolt
[49] is lubricated with grease, D00633 or grease, D00013.
4) Install the pin [54] in the nut [53].
(c) Connect the drive rod assembly [32] to the attach beam assembly [33]:
1) Put the drive rod assembly [32] in its position on the attach beam assembly [33].
2) Install the bushing [28], bolt [26], washer [27], washer [29] and nut [30] to attach the
drive rod assembly [32] to the attach beam assembly [33].
3) Install the pin [31] in the nut [30].
(d) Connect the adjust link assembly [41] to the aft fairing assembly [2]:
1) Put the adjust link assembly [41] in its location on the aft fairing assembly [2] with the
washers [55], washers [64], bushing [60] and bushing [61].
NOTE: Install the same number of washers [55] in the same location as you removed
them.
2) Install the bolt [62], washer [63], washer [58] and nut [57].
3) Tighten the nut [57]:
a) Tighten the nut [57] to 530-690 pound-inches (59.9-77.9 newton-meters) if the bolt
[62] is not lubricated.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-28
Page 413
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
b) Tighten the nut [57] to 345-425 pound-inches (39.0-48.0 newton-meters) if the bolt
[62] is lubricated with grease, D00633 or grease, D00013.
4) Measure the clearance between the washer [58] and the flange on the bushing [59].
5) If the clearance is not 0.010 to 0.025 inch (0.25 to 0.64 millimeter), change the location of
the washers [55]:
a) Remove the nut [57], washer [58], washers [55], washers [64], washer [63], bolt [62],
bushing [60] and bushing [61].
b) Change the location of the washers [55].
c) Install the bushing [60], bushing [61], bolt [62], washer [63], washers [55], washers
[64], washer [58] and nut [57].
d) Make sure the clearance between the washer [58] and the flange on the bushing
[59] is in the limit of 0.010 to 0.025 inch.
e) Tighten the nut [57] to 530-690 pound-inches (59.9-77.9 newton-meters) if the bolt
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
737-600-700-800-900 飞机维护手册5 AIRCRAFT MAINTENANCE MANUA(32)
