曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
12-22-51-640-803 Inboard Flap Outboard Ballscrew and Gimbal Lubrication (P/B 301)
27-51-00-440-801 Trailing Edge Flap System Reactivation (P/B 201)
27-51-00-820-802 Trailing Edge Flap Drive System Adjustment (P/B 501)
27-51-00-860-801 Trailing Edge Flap System Operation With Primary Control (P/B 201)
27-51-18-400-802 Inboard Flap Support Aft Fairing Installation (P/B 401)
29-11-00-860-801 Hydraulic System A or B Pressurization (P/B 201)
29-11-00-860-805 Hydraulic System A or B Power Removal (P/B 201)
C. Consumable Materials
Reference Description Specification
D00633 Grease - Aircraft General Purpose BMS3-33
D. Expendables/Parts
AMM Item Description AIPC Reference AIPC Effectivity
1 Ballscrew assembly 27-51-32-01-028 GUN 001-007, 121,
155-157, 201-999
6 Washer 27-51-32-01-015 GUN 001-007, 121,
155-157, 201-999
7 Collar 27-51-32-01-020 GUN 001-007, 121,
155-157, 201-999
12 Gimbal assembly 27-51-32-01-050 GUN 001-007, 121,
155-157, 201-999
13 Bolt 27-51-32-01-010 GUN 001-007, 121,
155-157, 201-999
E. Location Zones
Zone Area
542 Left Wing - Fairing Flap Support No. 3
553 Left Wing - Inboard Flap
642 Right Wing - Fairing Flap Support No. 6
653 Right Wing - Inboard Flap
F. Inboard Flap Outboard Ballscrew and Gimbal Installation
SUBTASK 27-51-32-420-001
(1) If you removed it, install the gimbal assembly [12] on the ballscrew nut [22]:
(a) Apply grease, D00633 to the inside and outside mating surfaces of the gimbal bushings [8].
GUN 001-099, 101-122, 156, 157, 201-999; GUN 155 POST 737-SL-57-077
(b) Apply grease, D00633 to the outside surfaces of the gimbal bushings [8].
GUN ALL
(c) Put the gimbal assembly [12] in its location on the ballscrew nut [22].
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-32
Page 406
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(d) Install the gimbal bushings [8] through the gimbal assembly [12] on the ballscrew nut [22].
(e) Install the bolts [13], washers [6] and collars [7] that attach the gimbal bushings [8] to the
gimbal assembly [12].
SUBTASK 27-51-32-420-002
(2) Connect the ballscrew assembly [1] to the yoke [17] on the transmission [15]:
(a) Turn the ballscrew nut [22] until it is at the forward end of the ballscrew assembly [1].
(b) Apply a layer of grease, D00633 to the mating surfaces of the yoke [17] and the ballscrew
assembly [1].
(c) Put the ballscrew assembly [1] into the yoke [17].
(d) Apply a layer of grease, D00633 to the shank and threads of the bolts [18].
(e) Install the bolts [18], washers [19], washers [20] and nuts [21] to attach the ballscrew
assembly [1] to the yoke [17].
(f) Make sure the ballscrew assembly [1] is installed correctly in the yoke [17]:
1) Turn the transmission [15] until the nut [24] on the U-joint [16] is up.
2) Turn the ballscrew nut [22] until the upstop is 1808 from the upstop [23] on the yoke [17].
3) If the ball returns [5] on the ballscrew nut [22] are not in the correct position, then
change the position of the ballscrew assembly [1]:
NOTE: On transmission No. 3, make sure the ball returns [5] on the ballscrew nut [22]
are on the outboard side. On transmission No. 6, make sure the ball returns [5]
on the ballscrew nut [22] are on the inboard side.
a) Remove the nuts [21], washers [20], washers [19] and bolts [18] that attach the
ballscrew assembly [1] to the yoke [17].
b) Turn the ballscrew assembly [1] 1808 in the yoke [17].
c) Install the bolts [18], washers [19], washers [20] and nuts [21].
(g) Tighten the nuts [21].
SUBTASK 27-51-32-420-003
(3) Connect the ballscrew assembly [1] with the gimbal assembly [12] to the carriage [3]:
(a) Move the gimbal assembly [12] to the downstop on the ballscrew assembly [1].
NOTE: On transmission No. 3, make sure the ball returns [5] on the ballscrew nut [22] are
on the outboard side. On transmission No. 6, make sure the ball returns [5] on the
ballscrew nut [22] are on the inboard side.
(b) Move the carriage [3] to align with the gimbal assembly [12].
(c) Apply grease, D00633 to the inside and outside surfaces of the carriage bushing [4] and
carriage bushing [11].
GUN 001-099, 101-122, 156, 157, 201-999; GUN 155 POST 737-SL-57-077
(d) Apply grease, D00633 to the outside surfaces of the carriage bushing [4] and carriage
bushing [11].
GUN ALL
(e) Install the carriage bushing [4] and carriage bushing [11] to attach the gimbal assembly [12]
to the carriage [3].
(f) Install the bolts [2], washers [10] and nuts [9] that attach the carriage bushing [4] and
carriage bushing [11] to the carriage [3].
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
737-600-700-800-900 飞机维护手册5 AIRCRAFT MAINTENANCE MANUA(51)
