S 865-002
(2)
Remove the hydraulic power if it is not necessary
(AMM 29-15-00/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
22-31-10
ALL ú ú 01 Page 504 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
AUTOTHROTTLE POWER LEVER ANGLE SYNCHRO - REMOVAL/INSTALLATION
_____________________________________________________________
1. General
_______
A. This procedure contains two tasks. The first task is for the removal of the Power Lever Angle (PLA) synchro. The second task is for the installation of the PLA synchro.
B. The PLA synchro is in the lower left area of the applicable engine.
TASK 22-31-11-004-018
2. Power Lever Angle Synchro Removal
__________________________________
A. Standard Tools and Equipment
(1) Rig Pin Kit - F70207
NOTE: Rig pin F70207-23 or MS20392-3C pin (optional), or
____ equivalent 0.248 (+0.000/-0.002)-inch diameter 3-inch long rod or bolt.
B. References
(1)
71-11-02/201, Fan Cowl Panels - Maintenance Practices
(2)
22-31-11/501, Autothrottle Power Lever Angle Synchro -Adjustment/Test
(3)
12-31-01/201, Left and Right Fan Cowl Panel
C. Access
(1)
Location Zone
502 Engine No. 1 - 7:00 o'clock position
602 Engine No. 2 - 7:00 o'clock position
(2)
Access
5746L Engine No. 1 - Left Fan Cowl Panel
5846R Engine No. 2 - Left Fan Cowl Panel
D. Prepare for the removal
S 864-001
(1) Open these circuit breakers on the P18-1 load control center:
(a)
AUTO THROTTLE AC
(b)
AUTO THROTTLE DC
S 864-017
(2) Do these tasks to prepare for the autothrottle PLA removal:
(a)
Set the thrust lever approximately 20 degrees angle to install the rig pin in part power rig hole R.
(b)
Install the DO-NOT-OPERATE identifier.
(c)
Open the left (right) fan cowl panel on the applicable engine (Ref 71-11-02/201).
(d)
Disconnect the electrical connector from the synchro.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
22-31-11
ALL ú ú 01 Page 401 ú Mar 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500
MAINTENANCE MANUAL
POWER LEVER ANGLE SYNCHROS (LEFT SIDE OF ENGINES)
SEE A
RIG PIN 1
SEE B
RIG PIN 1
CONTROL BOX
MEC FUEL
SEE C
CONTROL BOX RIG MARK (LOCATED ON UNDERSIDE OF FLANGE)
PLA SYNCHRO CONNECTOR
WIRE BUNDLE CLAMP
FWD
B
POWER LEVER ANGLE SYNCHRO
SEE E
INDEX MARK SYNCHRO GEAR
CLAMPING PLATES D
1 DIAMETER, 3 INCH LONG ROD OR BOLT ONE RIG PIN REQUIRED: F70207-23, 0R MS20392-3C, OR EQUIVALENT 0.248 (+0.000/-0.002)-INCH
A
PLA SYNCHRO MOUNTING BOLTS
CLAMPING PLATES
CSEE D
FLANGE INDEX MARK
POWER LEVER
ANGLE SYNCHRO
E
Autothrottle Power Lever Angle Synchro Installation
Figure 401
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址:737-300 400 500 AMM 飞机维护手册 自动飞行 AUTOFLIGHT 2(169)