27-61-00
ALL ú ú 01 Page 515 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
20` SPOILER FLIGHT INBOARD MINIMUM CLEARANCE SPOILER-TO-FLAP 2
SEE B
MIDFLAP
ASSEMBLY ARM ROD INPUT PACKAGE CONTROL ADJUSTMENT ROD (2 LOCATIONS) CHECKNUT B-B INBOARD FLIGHT SPOILER NO. 5 SHOWN (SPOILER NO. 8 EQUIVALENT) FWD
PISTON ROD CONTROL PACKAGE
DEVICES LOCKING
CHECKNUT
B ROD END PISTON
NOTE: THE AIRPLANE MUST BE SUPPORTED ON ITS LANDING GEAR WHEN YOU MEASURE THIS CLEARANCE.
2
THE SPOILER PANELS ARE NOT FLAT. MEASURE THE CLEARANCE AT THE NEAREST POINT. THERE IS NO MAXIMUM CLEARANCE BEACAUSE OTHER PARTS OF THE PANEL CAN HAVE A GREATER CLEARANCE. THE SPOILER HAS A 0.50 INCH (12.7 mm) PRELOAD AGAINST THE MIDFLAP.
Flight Spoiler Panel Adjustment Figure 504 (Sheet 2)
C79477
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-61-00
ALL ú ú 04 Page 516 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 865-134
WARNING:_______ MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE LE AND TE
FLAPS AND FLAP DRIVE MECHANISMS BEFORE YOU MOVE THE FLAP
CONTROL LEVER. WITH HYDRAULIC POWER REMOVED, THE FLAPS WILL
MOVE AUTOMATICALLY BY ELECTRICAL POWER WHEN YOU MOVE THE FLAP
CONTROL LEVER.
(5) Do this task: "Trailing Edge Flaps Retraction" (AMM 27-51-00/201).
NOTE: You must fully retract the trailing edge flaps with hydraulic
____ power. Keep the flap control lever in the UP position for 1 minute before you measure the clearance.
S 865-044
(6)
Put the speed brake lever in the DOWN position to lower all spoilers until the control package piston is fully retracted.
S 865-045
(7)
Turn the aileron control wheel clockwise to make sure that spoilers No. 1 thru 5 are in the fully down position.
S 225-046
(8)
Measure the clearance between the spoilers No. 1 thru 4 and the trailing edge flaps (Fig. 504):
(a)
Make sure the clearance at the nearest point between the spoilers No. 1 thru 4 and the trailing edge flaps is 0.02-0.16 inch(.508-4.064mm) (Section A-A). There is no specified maximum clearance.
S 225-139
(9)
Measure the clearance between the spoiler No. 5 and the trailing edge flaps (Fig. 504):
(a)
Make sure the clearance at the nearest point between the spoiler No. 5 and the trailing edge flaps is 0.055-0.075 inch. (1.397-1.905mm)
(b)
Extend the trailing edge flaps fully (AMM 27-51-00/201).
(c)
Adjust the piston rod end 1 turn (360 degrees) to lower the trailing edge of the spoiler to 0.567 inch.(14.402mm)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-61-00
ALL ú ú 22 Page 517 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 865-047
(10)
Turn the aileron control wheel counterclockwise to make sure that spoilers No. 8 thru 12 are in the fully down position.
S 225-048
(11)
Measure the clearance between the spoiler No. 8 and the trailing edge flaps (Fig. 504):
(a)
Make sure the clearance for the spoiler No. 8 is the same as the clearance for the spoiler No. 5.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：747-400 AMM 飞机维护手册 飞行操纵 FLIGHT CONTROLS 6(37)
