1) P7 Overhead Circuit Breaker Panel: a) 1F10, EIU C
G. Audio Test ADF System
S 715-011
(1) Do the ADF audio test (for both left ADF and right ADF).
(a) Connect a headphone to the captain's interphone audio jack panel.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
34-57-00
ALL ú ú 13 Page 507 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
(b)
Set the ADF/VOR selector switch on the captain's audio control panel to the ADF position for the applicable ADF system.
(c)
Set the ADF system volume control and cockpit speaker volume control to nominal setting.
(d)
Set the VOICE/RANGE switch on the captain's audio control panel to B (Both) position.
(e)
Make sure ADF audio sound can be heard loud and clear in the headphone. Readjust the ADF volume control and the cockpit speaker volume controls to make sure the ADF audio level can be changed.
H. ADF Bearing Accuracy and Standby Tuning Test ADF System
S 715-012
(1) Use the CDU to do the ADF bearing accuracy and standby tuning test.
(a)
Close these circuit breakers:
1) P7 Overhead Circuit Breaker Panel: a) 1F09, EIU L b) 1F10, EIU C
(b)
Open these circuit breakers:
1) P7 Overhead Circuit Breaker Panel: a) 3C01, FMCS FMC L b) 3C23, FMCS FMC R
(c)
Push the NAV RAD mode select key on the left and right CDUs. 1) The left and right CDUs display the ALTN NAV RADIO page.
(d)
Enter the frequency of a usable local ADF beacon station or the frequency of a usable local AM broadcast station on the left and right CDUs. 1) The left and right CDUs display the entered frequency.
(e)
Push the 3L LSK on the left CDU to tune the Left ADF.
(f)
Push the 3L LSK on the right CDU to tune the Right ADF.
(g)
Make sure the left and right CDUs display the desired frequency under the small font ADF letters.
(h)
Make sure the L ADF and R ADF pointers on the captain's ND point to the same bearing.
S 865-028
(2) Put the Safety Sensitive Systems back to the condition before Air Mode (AMM 32-09-02/201).
I. Put the Airplane Back to Its Usual Condition
S 865-014
(1) Remove electrical power if it is not necessary (AMM 24-22-00/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
34-57-00
ALL ú ú 14 Page 508 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
AUTOMATIC DIRECTION FINDER (ADF) RECEIVER - REMOVAL/INSTALLATION
________________________________________________________________
1. General
_______
A. This procedure has two tasks. One is the removal of the ADF receiver. The other is the installation of the ADF receiver.
B. The left, B87 and right, B88 ADF receivers are installed on the E9 electrical equipment rack in the center equipment center. This center can be accessed by a door located at the bottom centerline of the fuselage.
C. The removal/installation procedure is the same for the left and right ADF receiver, with the exception of the circuit breakers.
D. The CMC has a Shop Faults menu item for the Left and Right ADF receivers, but neither ADF receiver can give shop fault information.
NOTE: Do not request Shop Faults data from the Left or Right ADF
____
receiver.
TASK 34-57-01-004-001
2. Remove the ADF Receiver
_______________________
A. References
(1)
20-11-22/401, E/E Rack Mounted Components
(2)
20-41-02/201, Electrostatic Discharge Sensitive Devices
(3)
IPC 34-57-10, Fig. 1
B. Access
(1)
Location Zone
129 Keel Beam
(2)
Access Panel
125B Center Electronics Access Door
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：747-400 AMM 飞机维护手册 导航 NAVIGATION 3(98)
